NOTES
A If you are installing in
frameless cabinets,
it may be necessary
to install 1/2" wide
cleats to accept drawer
mounting screws. See
drawer for mounting
screw locations.
B Install a 2"x2" or 2"x4"
anti-tip block against
rear wall, 9" from floor
of cutout to bottom
of block. The anti-tip
block must be installed
to prevent the drawer
from tipping forward
when opened and
loaded. Failure to add
the anti-tip block could
result in personal injury.
C When installing the
warming drawer below
a cabinet drawer, a
solid barrier must be
installed at least above
the warming drawer
to block access. Use
any solid material such
as 1/4" thick plywood.
Allow at least 1/4"
air gap between the
barrier and the top of
the warming drawer.
Observe the 5" min.
above the floor or 1"
min. above the toe kick
installation height.
D When installing two
warming drawers side
by side, install them
in separate cut-outs
and allow a 2" min. gap
between each cut-out.
E The warming drawer
may be supported by
either a solid bottom or
2"x2" or 2"x4" runners.
The support must
be level and rigidly
mounted, flush with
the bottom edge of the
cut-out (there is no way
to level the drawer once
it has been installed,
so make sure that the
supports are level). The
floor or runners must be
capable of supporting
at least 150 lbs.
For more details refer
to the installation
instructions for this
product.
INSTALLATION BELOW A CABINET DRAWER
PROVIDING CABINET SUPPORT
INSTALLING ANTI-TIP BLOCKS
SIDE BY SIDE INSTALLATION
Product Specification Created 8/14
GE Monogram
®
30" Warming Drawer
ZTD910SFSS
SIDE VIEW
FRONT VIEW
TOP VIEW
28 1/2"
(72.4)
min. cutout width
23 1/2"
(59.7)
min. cutout width
1/4"
(.6)
min.
1"
(2.5)
min.
Above
toe-kick
2"
(5.1)
min.
Between cut-outs
2"
(5.1)
x 4"
(10.2)
or Equivalent Runners
Install
2"
(5.1)
x 4"
(10.2)
or
2"
(5.1)
x 2"
(5.1)
Anti-tip Block against
rear cabinet wall 9" from
floor to bottom of block
Side cleats
9 1/4"
(23.5)
Cut-out
height
30"
(76.2)
25"
(63.5)
23 1/2"
(59.7)
2"
(5.1)
x 4"
(10.2)
or
2"
(5.1)
x 2"
(5.1)
Runners or Solid Bottom
ZDT910SFSS
SIDE VIEW
FRONT VIEW
TOP VIEW
28 1/2"
(72.4)
min. cutout width
23 1/2"
(59.7)
min. cutout width
1/4"
(.6)
min.
1"
(2.5)
min.
Above
toe-kick
2"
(5.1)
min.
Between cut-outs
2"
(5.1)
x 4"
(10.2)
or Equivalent Runners
Install
2"
(5.1)
x 4"
(10.2)
or
2"
(5.1)
x 2"
(5.1)
Anti-tip Block against
rear cabinet wall 9" from
floor to bottom of block
Side cleats
9 1/4"
(23.5)
Cut-out
height
30"
(76.2)
25"
(63.5)
23 1/2"
(59.7)
2"
(5.1)
x 4"
(10.2)
or
2"
(5.1)
x 2"
(5.1)
Runners or Solid Bottom
ZDT910SFSS
SIDE VIEW
FRONT VIEW
TOP VIEW
28 1/2"
(72.4)
min. cutout width
23 1/2"
(59.7)
min. cutout width
1/4"
(.6)
min.
1"
(2.5)
min.
Above
toe-kick
2"
(5.1)
min.
Between cut-outs
2"
(5.1)
x 4"
(10.2)
or Equivalent Runners
Install
2"
(5.1)
x 4"
(10.2)
or
2"
(5.1)
x 2"
(5.1)
Anti-tip Block against
rear cabinet wall 9" from
floor to bottom of block
Side cleats
9 1/4"
(23.5)
Cut-out
height
30"
(76.2)
25"
(63.5)
23 1/2"
(59.7)
2"
(5.1)
x 4"
(10.2)
or
2"
(5.1)
x 2"
(5.1)
Runners or Solid Bottom
ZDT910SFSS
A
A
D
E
B
B
C
