GE Monogram ZISW420DM Installation Information Download Page 3

Monogram.

ZISW420DM – GE Monogram 42" Built-In Refrigerator 

with Dispenser and Water Filter

3/4" OVERLAY PANEL DIMENSIONS

For a more custom appearance, overlay panels may
be installed on trimmed models. The overlay panel
must be secured to a 1/4" thick backer panel which
slides into the trim. A spacer panel 0.10" thick must
be placed  between the overlay and backer panel. 

Assemble the panels with glue and screws. 
• Center the spacer panel on the backer panel, left to

right and top to bottom. Secure the panels with glue.

• Center the spacer and backer panel on the overlay

panel and secure with glue and screws. Screws
must be countersunk into the backer panel.

3/4"

Overlay

Panel

1/4"

Backer

Panel

Door

.10"

Spacer

Spacer Panel

Overlay Panel

Backer Panel

.250"  +  .10"  +  .750"  =  1.100" Total Panel Thickness

NOTE

: Left-to-right offset

is not always equal to
top-to-bottom offset.

IMPORTANT NOTE – Dispenser Models

The refrigerator is supplied with two dispenser trims, one

for framed panels and one for overlay panels. The overlay

dispenser trim is designed to fit a total panel thickness 
of 1.100".
• If the panel is less than 1.100" a noticeable gap may be

created around the dispenser trim. 

• If the panel is more than 1.100" the dispenser trim cannot

be secured to the door.

• The overlay panel must be constructed according to the

specifications shown to achieve the correct total thickness.

• Alternative panel construction methods such as securing a

3/4" panel to a 1/4" backer panel cannot be used. Another
method, routing a 3/4" thick panel on all sides cannot be
used. These methods  will not result in the required 1.100"
panel thickness. 

Fresh Food 

Panel

Freezer

Panel

E

D

F

G

A

B

Grille Panel

C

Dispenser

Cutout

9-5/8"

Dispenser Cutout

15-3/8"

A

B

C

D

E

F

G

1/4” Backer Panel

39-7/8

9-1/2

68-3/8

14-9/16

24-9/16

.10” Spacer Panel

39

8-5/8

67

13-1/4

23-1/4

3/4" Overlay Panel

40-1/8

9-3/4

68-5/8

14-13/16

24-13/16

17-15/16

3-1/8

*Dispenser

Cutout Position

*Cut the dispenser opening after the backer, spacer and

overlay panels have been assembled. 

IMPORTANT NOTE

: Maximum total weight for assembled fresh

food panel is 50 pounds and 30 pounds for freezer panel.

As an ENERGY STAR

®

 Partner, 

GE has determined that this product 

meets the ENERGY STAR

®

 

guidelines for energy efficiency.

For answers to your Monogram,

® 

GE Profile

or 

GE

®

appliance questions, visit our website at

GEAppliances.com or call 
GE Answer Center

®

service, 800.626.2000.

R

Listed by
Underwriters
Laboratories

Specification Revised 8/03

110176

Summary of Contents for Monogram ZISW420DM







Reviews: