GE Monogram ZIF36N LH Installation Instructions Manual Download | Manualshive

Page: 1 / 40

background image

These Monogram refrigerators and
freezers are designed to be customized
with decorator door and grille panels.
Field installed panels are required.

Factory installed trim will
accommodate 1/4

″

thick custom

panels or optional Lexan

®

and stainless

steel panel kits.

Optional trim kits allow an even
broader range of custom appearance
options.

Read this booklet carefully to
accomplish the desired appearance and
to insure a trouble free installation.

This booklet contains information and
illustrations to demonstrate custom
possibilities. Custom door and grille
panel sizes vary to accommodate the
kit being used. Dimensions for each
application are included and can
be faxed or sent to the cabinet
manufacturer so that the panels
can be constructed accurately.

Custom Options Guide and

Installation
Instructions

With Custom Panel Dimensions
and Trim Kit Installation Instructions

36

″

Refrigerators and 36

″

Freezers

ZIR36N LH – All Refrigerator

ZIR36N RH – All Refrigerator

ZIF36N LH – All Freezer

ZIF36N RH – All Freezer

monogram.com

1
2
3
...
»

Summary of Contents for Monogram ZIF36N LH









































Reviews:

No comments

Related manuals for Monogram ZIF36N LH

Brand: Wagan Pages: 7

Brand: Dacor Pages: 2

RISE JFFCF72DKL

Brand: Jenn-Air Pages: 3

Brand: GE Pages: 104

Shelleyspeed SPRD36P-50NE

Brand: Delfield Pages: 2

Brand: R&D Pages: 57

Brand: Maytag Pages: 66

Brand: KÜPPERBUSCH Pages: 64

Brand: Ariston Pages: 28

Brand: ETNA Pages: 56

Brand: V-ZUG Pages: 112

Brand: Philco Pages: 156

Brand: Westinghouse Pages: 11

Brand: ZANKER Pages: 36

Brand: Magic Chef Pages: 11

Brand: Jacky's Pages: 40

Brand: PARADISE GRILLS Pages: 14

Brand: Magic Chef Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands