05-4847A01-GB, Rev. B
MDS SD Series Setup Guide
5
FCC Part 15 Notice
Operation is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept any inter-
ference received, including interference that may cause undesired opera-
tion. Any unauthorized modification or changes to this device without the
express approval of the manufacturer may void the user’s authority to op-
erate this device. Furthermore, this device is intended to be used only
when installed in accordance with the instructions outlined in this manual.
Failure to comply with these instructions may void the user’s authority to
operate this device.
Industry Canada Notice
This Class A digital apparatus complies with Canadian ICES-003.
Modifications:
Any modifications made to this device that are not approved by GE MDS
LLC, Inc. may void the authority granted to the user to operate this equip-
ment.
Servicing Precautions
When servicing energized equipment, be sure to wear appropriate Per-
sonal Protective Equipment (PPE). During internal service, situations
could arise where objects accidentally contact or short circuit components
and the appropriate PPE would alleviate or decrease the severity of po-
tential injury. When servicing radios, all workplace regulations and other
applicable standards for live electrical work should be followed to ensure
personal safety.
Manual Revision and Accuracy
This manual was prepared to cover a specific version of firmware code.
Accordingly, some screens and features may differ from the actual unit
you are working with. While every reasonable effort has been made to
ensure the accuracy of this publication, product improvements may also
result in minor differences between the manual and the product shipped
to you. If you have additional questions or need an exact specification for
a product, please contact GE MDS using the information at the back of
this guide. In addition, manual updates can be found on our web site at
www.gemds.com
Environmental Information
The manufacture of this equipment has required the ex-
traction and use of natural resources. Improper disposal
may contaminate the environment and present a health
risk due to hazardous substances contained within. To
avoid dissemination of these substances into our environ-
ment, and to limit the demand on natural resources, we
encourage you to use the appropriate recycling systems for disposal.
These systems will reuse or recycle most of the materials found in this
equipment in a sound way. Please contact GE MDS or your supplier for
more information on the proper disposal of this equipment.
Battery Disposal
—This product may contain a battery. Batteries must
be disposed of properly, and may not be disposed of as unsorted munici-
pal waste in the European Union. See the product documentation for spe-
cific battery information. Batteries are marked with a symbol, which may
include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For
proper recycling return the battery to your supplier or to a designated col-
lection point. For more information see: www.weeerohsinfo.com.
Product Test Data Sheets
Test Data Sheets showing the original factory test results for this unit are
available upon request from the GE MDS Quality Leader. Contact the
factory using the information at the back of this manual. Serial numbers
must be provided for each product where a Test Data Sheet is required.
CSA/us Notice
This product is approved for use in Class 1, Division 2, Groups A, B,
C & D Hazardous Locations. Such locations are defined in Article 500 of
the National Fire Protection Association (NFPA) publication NFPA 70,
otherwise known as the National Electrical Code. The transceiver has
been recognized for use in these hazardous locations by the Canadian
Standards Association (CSA) which also issues the US mark of approval
(CSA/US). The CSA Certification is in accordance with CSA STD C22.2
No. 213-M1987.
CSA Conditions of Approval: The transceiver is not acceptable as a
stand-alone unit for use in the hazardous locations described above. It
must either be mounted within another piece of equipment which is certi-
fied for hazardous locations, or installed within guidelines, or conditions of
approval, as set forth by the approving agencies. These conditions of ap-
proval are as follows: The transceiver must be mounted within a separate
enclosure which is suitable for the intended application. The antenna feed
line, DC power cable and interface cable must be routed through conduit
in accordance with the National Electrical Code. Installation, operation
and maintenance of the transceiver should be in accordance with the
transceiver's installation manual, and the National Electrical Code. Tam-
pering or replacement with non-factory components may adversely affect
the safe use of the transceiver in hazardous locations, and may void the
approval. A power connector with screw-type retaining screws as sup-
plied by GE MDS must be used.
CE Mark and Radio Equipment Directive (RED) Notice
(applies
to select bands of SD04 product only)
Product that is CE marked is compliant with European Union Radio
Equipment Directive 2014/53/EU.
GEMDS products employ a variety of wireless technologies and frequen-
cies. These can include, cellular M2M, WIFI, and licensed narrowband ra-
dio frequencies. The user is responsible to ensure that proper spectrum
licenses are obtained for all licensed uses, carrier SIMs are authorized for
M2M cellular, and proper antenna gain is used to maintain local regula-
tory compliance.
Hazardous Locations Notice
WARNING
EXPLOSION HAZARD!
Do not disconnect equipment unless power has
been switched off or the area is known to be non-
hazardous. Refer to Articles 500 through 502 of the
National Electrical Code (NFPA 70) for further infor-
mation on hazardous locations and approved Divi-
sion 2 wiring methods.
NO USER SERVICEABLE PARTS INSIDE
1.
