background image

16  |  

GE Oil & Gas

- VariPak valves with Cv max. 3.8 do not have seatring 

gaskets (2).

5.4 REASSEMBLY (Figures 5, 15, 19, 20, 24, 25, 26, 27, 
28 and 29)
Before reassembly, thoroughly clean the inside of the 
valve body and parts, paying particular attention to 
gasket seating surfaces and contact surfaces. Make 
sure to use a new seat-ring gasket (2) and new packing 
(6) during reassembly.

A.  Insert a new seat-ring gasket (2) into valve body (13), 

then fit seat ring (3), making sure that the gasket is 
correctly centered on the seat-ring shoulder. Turn it 
so that one of its ports is lined up with the valve body 
outlet orifice.

Note: If the maximum Cv is less than 0.10, first fit the 

seat ring (3e) on the new gasket (2), taking the same 
precautions as above. Then fit the spacer (3f), turning it 
so that one of its ports is turned towards the body outlet 
orifice.
VariPak valves with a maximum Cv of 3.8 do not include 

a seat-ring gasket (2).

B.  Carefully apply Never Seez grease or equivalent to 

the threads and bottom of the seat-ring retainer 
(4). Using a 9/16" or 14 mm piece of hex stock and a 
wrench, torque the retainer to 59 ftlb or 8 daN.m for 
stainless-steel reinforced graphite gaskets or 40 ft-lb 
or 5.5 daN.m for glass-filled PTFE gaskets (see figure 
19).

Note: Torque the retainer to 30 ft-lb or 4 daN.m for 
valves with a maximum Cv of 3.8.
C.  Insert the plug and stem assembly into the seat 

ring. For valves with a maximum Cv < 0.10, check 

that there are no friction points in the plug stroke. 
If a friction point is detected, loosen retainer (4) 
and reposition seat ring (3e) until the stem slides 
smoothly. Fit spacer (5), turning it so that one of its 
holes is aligned with safety pin (11) hole in the valve 
body.

Note: For valves with a maximum Cv less than 0.10, 

check that the retaining ring (182) is fitted on the plug 
before fitting the plug in the spacer (3f). If the retaining 
ring is worn or damaged, replace it.

 

Figure 19 - Tightening the seat-ring retainer (4)

D.  Wind two layers of PTFE tape around the safety pin 

(11). Screw the pin into the bonnet five and a half to 
six turns as from the thread engagement point.

 

Note: To determine the thread engagement point:

 

- Screw the safety pin about one turn.

 

- Pull the safety pin out while unscrewing it.

E.  Fit the packing, making sure that the skive cut of 

each packing ring is located 120° away from the that 
of the adjacent ring. Push the rings down slightly 
using a 1/2" sch., size 160 tube. Fit the packing 
follower (9) onto the plug stem. 

F.  Fit actuator bracket (108) and secure it with two 

nuts (8a). Slip packing flange (10) onto plug stem. 
Handtighten the two packing flange nuts and add 
one full turn with the wrench.

G.  Fit, in the following order, grommet plate (101), 

conical compression spring (106) and its spring 
button (102) (see position in figure 26 and 27). Screw 
nut (103) and clevis (104a) on the plug stem.

Adjust the nut and clevis without locking them together 
until the clevis holes are positioned approximately:

 

-  2.3 mm below the alignment of the pin holes in 

the actuator bracket (108) for the VariPak 28001 
single-lever valve (see figure 15).

 

-  1.5 mm above the alignment of the pin holes in 

the actuator bracket (108) for the VariPak 28002 
adjustable-Cv valve (see figure 20).

Note: Measuring this distance can be simplified by fitting 
pins (105), (184) and (18) into their holes.

Summary of Contents for Masoneilan VariPak 28000 Series

























Reviews: