GE MAC 600 SPY Service Manual Download Page 69

Page: 69 / 127

Revision G

MAC

600

4-19

2047426-002

Maintenance:

Preparing System for FRU Replacement

9. Enter the serial number and option code (optional) as described in

“Restoring Setup”

on page 4-30.

10. Adjust the time and date. See

MAC 600 operator’s Manual

for setting

date and time.

11. If possible, set the configuration to the previous user settings. If not,

select the default settings.

Replacing the Daughter PCB assembly

1. Open the device as described in

“Opening the Device”

on page 4-8.

2. Remove the top cover assembly from the bottom cover.

3. Disconnect the display cable connector from the J2 connector on the

daughter PCB.

4. Press the snap for daughter board using the nose pliers and lift the

daughter board to detach from the snap.

5. Repeat step 4 for all the 3 snap features to completely remove the

daughter board from the display holder snap fit mechanism.

6. Align and fix the new daughter board to the daughter board-

mounting bracket snap fit mechanism.

7. Fix the ferrite with double-sided tape in line with J1.

8. Connect the display cable connector to the J2 connector on the

daughter PCB.

Table 4-10. Replacing the Daughter PCB Assembly

Legend

Description

Press the snap using a nose plier. Lift the
PCB board up.

Summary of Contents for MAC 600 SPY
































































































































Search results

Summary of Contents for MAC 600 SPY

Reviews:

Related manuals for MAC 600 SPY

Brands by name

Popular brands

GE MAC 600 SPY, Service Manual

Search results

Summary of Contents for MAC 600 SPY

Reviews:

Related manuals for MAC 600 SPY

Brands by name

Popular brands