manualshive.com logo in svg

GE Mabe GLD8110, Technical Service Manual, Page: 19 / 27

Share
Download
GE Mabe GLD8110 Technical Service Manual Download Page 19

 

‐ 

19 

‐ 

 

Door Panel                                                                                                                                             

 
The door panel covers the main control board, detergent cup, vent, wax motor, louver, and door-interlock switch. 
   
The outer door panel is held in place by 14 screws (7 Phillips head screws per side ).   

 

 
 
 
 
 
 
 
 
 
 
 

Note: Ribbon cable(s) connect the keypad membrane (2-digit display on some models) to the control board. Due to 
the ribbon length, care must be taken when removing the door panel to ensure that the ribbon cable(s) are not 
damaged.   
 

 

Membrane Keypad                                                                                                                                 
 

The door panel must be removed to access the membrane keypad (see 

Door Panel 

).   

z

 

When removing the membrane keypad, peel the keypad from right to left.   

z

 

When installing, make sure the membrane button areas and lights align with the keypad.   

z

 

On models with an LED display, the display is held in place plastic clip. 

 

Note: When replacing the keypad membrane, always run the 

Test mode   

calibrate the keypad membrane to the 

control board.   

 

 
 

 

 

Summary of Contents for Mabe GLD8110




























Reviews:

No comments