GE Multilin
M60 Motor Protection System
9-3
9 MAINTENANCE
9.2 BATTERIES
9
9.2 BATTERIES
9.2.1 REPLACE BATTERY
When required, the battery can be replaced. Because the power supply module contains the battery and there are two pos-
sible power supplies, two procedures are possible. Check the power supply module or use the photographs here to deter-
mine which procedure to use.
a) REPLACE BATTERY FOR RH POWER SUPPLY
When required, the battery can be replaced. The power supply module contains the battery.
To avoid injury, ensure that the unit has been powered off for a minimum of three minutes
before replacing the battery.
Risk of fire if battery is replaced with incorrect type or polarity.
To replace the battery:
1.
Turn off the power to the unit.
2.
Wait a minimum of three minutes to ensure that there is no power to the battery.
3.
As outlined in the previous section, open the unit by sliding up the latch on the right side of the front panel and opening
the panel to the left.
4.
Unscrew the bracket on the front left of the unit so that you can open fully the front panel to access the power supply
module, which is typically in the first slot on the left side.
5.
Simultaneously pull the ejector clips at the top and bottom of the power supply module and remove the module.
6.
Unscrew the screw that attaches the metal cover to the module.
7.
Slide the metal cover away from the clips about 1 cm (1/4 inch) and remove the cover.
8.
Unclip the black plastic holder that keeps the battery in place. The plastic clips into the socket at the bottom on both
sides. Use a flat-head screwdriver if you cannot unclip the plastic with your fingers.
9.
Observe the + and - polarity of the battery and replace it with the same polarity as marked on the battery holder.
Replace the battery with the identical make and model. For example, do not use a rechargeable battery.
Figure 9–3: BATTERY LOCATION ON RH POWER SUPPLY MODULE
10. Reinstall the battery clip and the metal cover, and reinsert the power supply module into the unit.
11. Power on the unit.
12. Dispose of the old battery as outlined in the next section.
Summary of Contents for M60 UR Series
