background image

Modifications reserved 

Page 8/65 

OPM_LPS_3UO_50K_60K_1US_V010.doc 

Operating Manual 

LP 33U Series 30 & 40 kVA

 

Safety symbols and warnings 

 
 

Safety warnings

 

The text of this manual contains some warnings to avoid risk to the persons and to avoid damages to 
the UPS system and the supplied critical loads. 
 
The non-observance of the warnings reminding hazardous situations could result in human injury and 
equipment damages. 

 

Please pay attention to the meaning of the following warnings and symbols. 

 

 
Throughout this manual the following symbols are defined: 

 

 

WARNING, if instruction is not followed injury or serious equipment damage may 
occur! 

 

 

CAUTION, internal parts have dangerous voltage present. 
Risk of electric shock! 

 

 

PE (Earth) – GND (Ground) 
PROTECTIVE GROUNDING TERMINAL: 
A terminal which must be connected to earth ground prior to making any other 
connection to the equipment. 

 

 

A terminal to which or from which an alternating (sine wave) current or voltage 
may be applied or supplied. 

 

 

A terminal to which or from which a direct current or voltage may be applied or 
supplied. 

 

 

This symbol indicated the word “phase”. 

 

 

This symbol indicates the principal on/off switch in the on position. 

 

 

This symbol indicates the principal on/off switch in the off position. 

 

Summary of Contents for LP 33U Series


































































Reviews: