manualshive.com logo in svg

GE JVM1500 Series, Installation Instructions Manual

Share
Download
GE JVM1500 Series Installation Instructions Manual Download Page 19

19

OUTSIDE TOP EXHAUST

(Vertical Duct)

C

Installation Instructions

INSTALLATION OVERVIEW

C1. 

Attach Mounting Plate to Wall

C2.

Prepare Top Cabinet 

C3.

Adjust Blower

C4.

Install Adapter

C5.

Mount the Oven

C6.

Adjust Exhaust Adapter

C7.

Connect Ductwork

ATTACH THE MOUNTING
PLATE TO THE WALL

Attach the plate to the wall using toggle bolts. At least
one wood screw must be used to attach the plate to 
a wall stud.

Remove the toggle wings from the bolts.

Insert the bolts into the mounting plate through
the holes designated to go into drywall and
reattach the toggle wings to 

3

⁄

4

″

onto each bolt.

2

1

C1

To use toggle bolts:

Place the mounting plate against the wall and
insert the toggle wings into the holes in the wall 
to mount the plate.

NOTE: 

Before tightening toggle bolts and wood screw,

make sure the tabs on the mounting plate touch the
bottom of the cabinet when pushed flush against the
wall and that the plate is properly centered under 
the cabinet.

CAUTION: 

Be careful to avoid pinching fingers

between the back of the mounting plate and the wall.

Tighten all bolts. Pull the plate away from the wall
to help tighten the bolts.

4

3

Wall

Mounting
Plate

Spacing for Toggles 
more than wall thickness

Bolt End

Toggle

Bolt

Toggle Wings

Summary of Contents for JVM1500 Series

























Reviews:

No comments

Brands by name

Popular brands

Load more brands