manualshive.com logo in svg

GE JN322, JN334, JN335, JN634, JN635, JV322, JV324, JV332, JV334, JV335, JV624, JV634, JV635, Use And Care Manual, Page: 9 / 12

Share
Download
GE JN322, JN334, JN335, JN634, JN635, JV322, JV324, JV332, JV334, JV335, JV624, JV634, JV635 Use And Care Manual Download Page 9

Lamp Replacement

Remove the lamp and replace with an ordinary 
base lamp bulb NOT MORE THAN 60 WATTS.

Models JN334, JN335, JN634,

To remove the lamp cover, if desired:

JN635, JV324, 

 JV335,

● 

Press the sides with 2 fingers until the side prongs

JV624, JV634, JV635 have a

are released.

lamp cover.

● 

Lift the lamp cover and slide towards you in one

The lamp cover need not be

motion.

removed for lamp removal

To replace the lamp cover:

or installation.

● 

Insert the prong located at the end of the cover into

the 

 

CAUTION: Let the lamp cool completely before

 

● 

Gently push the cover up and press the sides to fit

removing. A warm or hot bulb may break if
touched with a moist cloth or hand.

the side prongs into the side openings.

● 

Release and the cover will lock in position.

9

Summary of Contents for JN322, JN334, JN335, JN634, JN635, JV322, JV324, JV332, JV334, JV335, JV624, JV634, JV635













Reviews:

No comments