GE JN322, JN334, JN335, JN634, JN635, JV322, JV324, JV332, JV334, JV335, JV624, JV634, JV635 Use And Care Manual Download Page 1

Use and Care of Recirculation Hood Models JN322, JN334, JN335,

 

 JN635 and Ventilating Hood Models JV322, JV324, JV332,

JV334, JV335, JV624, JV634, & JV635

IMPORTANT SAFETY

C. When cutting or drilling into wall or ceiling,

INSTRUCTIONS

 not damage electrical wiring and other

hidden utilities.

WARNING- 

 REDUCE THE RISK

D. 

 fans must always be vented to

OF FIRE, ELECTRIC SHOCK, OR

the outdoors.

INJURY TO PERSONS, OBSERVE

E. 

If this unit is to be installed over a tub or

THE FOLLOWING:

shower, it must be marked as appropriate
for the application.

A. 

Use this unit only in the manner intended

by the manufacturer. If you have any questions,

WARNING 

 reduce the risk 

 fire,

contact the manufacturer.

 

 

 ductwork.

B. 

Before servicing or cleaning 

 switch

power off at service panel and lock service

 When using your hood...

panel to prevent power 

 being switched

on accidentally.

● 

Never leave surface units unattended   high

For general ventilating use only. 

 not use

settings. 

 causes smoking and greasy

to exhaust hazardous or explosive materials

 that may ignite and spread if hood is

and vapors.

used. Use surface unit heat settings recommended
by 

 manufacturer and adequate-size utensils.

When you get 

 new hood...

 Never use your cooking appliance for warming,

or heating the room. The electrical wiring of 

 Have it installed and properly grounded by a

range hood may not withstand the 

resulting

qualified technician in accordance with the

excessive 

installation instructions.

● 

Keep the hood clean and clean grease filter or

● 

Have the installer show you the location of

the hood circuit breaker or fuse and mark it for

replace combination filter as recommended to
maintain good venting and to avoid grease fires.

easy reference.

● 

 the time to read our suggestions for best use.

WARNINGTO REDUCE THE RISK

 A RANGE 

 GREASE 

WARNIN& 

 REDUCE 

 RISK

OF FIRE, ELECTRIC SHOCK, 

A. 

Keep 

 filters and grease laden

INJURY TO PERSONS, OBSERVE

surfaces clean.

THE FOLLOWING:

B. 

 

 ON when cooking

at high heat.

A. 

Installation work and electrical wiring must be

done by qualified person(s) in accordance with

C. Use high range settings on range only

 applicable codes and standards, including

when necessary. 

 oil slowly   low

 construction.

to medium setting.

B. The 

combustion airflow needed for safe

D. 

Don’t leave range unattended when cooking.

operation of fuel-burning equipment maybe

E. 

Always use cookware and utensils appropriate

affected by this unit’s operation. Follow the

for the type and amount of food being prepared.

heating equipment manufacturer’s guideline and

(continued 

safety standards such as those published by the
national Fire Protection Association 
and 

 American Society for Heating

Refrigeration and Air Conditioning Engineers

(ASHRAE), and the local code authorities.

Turn the page for Operation and Maintenance instructions.

GE Quality Product

Summary of Contents for JN322, JN334, JN335, JN634, JN635, JV322, JV324, JV332, JV334, JV335, JV624, JV634, JV635













Reviews: