GE JKP15 Series Installation Instructions Manual Download Page 11

D1

D2

D3

D4

D5

The oven door is heavy. You may need

help lifting the door high enough to

slide it into the hinges slots. Do not lift

the door by the handle.

11

Replacing the Oven

Door

D

Installation Instructions

Pick the Oven Door up by

placing one hand on each

side. The door is heavy so

you may need help. Do not

lift the door by the handle.

Place the notch of the

hinge arm into the

bottom edge of the

hinge slot.

Open the oven door as

far as it will open.

Push the hinge locks

up against the front

frame of the oven

cavity, to the locked

position.

Close the oven door.

Replacing the Oven Door

Hinge in

Locked Position

Notch of 

Hinge Securely 

Fitted into Bottom 

of Hinge Slot

Hinge Arm

Bottom Edge
Of Slot

Hinge Notch

Installing the Bottom

Trim

C4

a.

Place the bottom trim centered over the

pre-drilled mounting holes. Tape the edges

of the trim down to maintain the alignment.

Trim 

Screw

Lower

Trim

Side 

Trim

Side 

Trim

Preparing for the bottom

Trim Installation

a.

  With oven installed, take the bottom trim

      and center it on the bottom front edge of

      the cabinet opening.

b.

  Using the trim as

     a template mark

     the center of

     each slot (three

     total) where

     the mounting

     holes will be

     drilled.

c.

  Remove the trim.

d.

  Drill pilot holes into the center of each

      template mark.

Remove Lower Trim

Before Pre Drilling

Mounting Holes

With Lower Trim

In Position

Mark (3) Mounting

Hole Locations

With Lower Trim

In Position

Mark (3) Mounting

Hole Locations

C3

IMPORTANT:  If this unit is ever removed

from the cabinet or the cavity is ever

pulled out for service, the trim must be

removed first or damage to the trim will

occur.

b.

Using the three pan head trim screws

provided secure the bottom trim to the

bottom edge of the cabinet.

Summary of Contents for JKP15 Series













Reviews: