GE JKP15 Series Installation Instructions Manual Download Page 1

Before you begin

Read these instructions carefully and completely

IMPORTANT

-Save these instructions for

local inspector’s use.

IMPORTANT

-Observe all governing

codes and ordinances.

• Note to Installer- Be sure to leave these

instructions with the consumer.

• OWNER- Keep these instructions for future

reference.

27” Built In Wall Oven

Installation

Instructions

JKP15, JKP18, JKP27, JKP45, JKP56  JKS05,
ZEK937, ZEK957

• ATTENTION INSTALLER!!

All electric wall ovens must be hard wired

(direct wired) into an approved junction

box. A “plug and receptacle” is NOT permit-

ted on these products

• NOTE- This appliance must be properly

grounded.

Parts Included

1/8” Drill Bit &

Electric or

Hand Drill

Phillips

Screwdriver

Strain Relief

Clamp for

1/2” conduit

Junction

Box

Wire Nuts

36” of String

 Bottom Trim

Single Ovens
4 flat head screws (side trim)
3 pan head screws (bottom trim)
Double Ovens
8 flat head screws (side trim)
3 Pan head screws (bottom trim)

Tools You Will Need

Pub. No. 31-10473
229C

4053P452

1

“If you have questions, call 800-GE-CARES 

or visit our website at:

www.GEAppliances.com”

Materials Needed

Summary of Contents for JKP15 Series













Reviews: