background image

13

Installation Instructions

MAKING THE LP CONVERSION

SAFETY INFORMATION YOU
SHOULD KNOW 

The pressure regulator and burner orifices
are set for natural gas. To use Propane Gas,
the regulator and burner orifices must be
converted. The LP orifice spuds for the
cooktop burners can be located in the
literature package attached to the regulator.

CAUTION:

The cooktop, as shipped

from the factory, is set for use with natural
gas. If you wish to use your cooktop with
Liquefied Petroleum (Propane) gas, you must
first replace the orifices and convert the
pressure regulator.

WARNING:

This conversion must 

be performed by a qualified installer or gas
supplier in accordance with the manufacturer’s
instructions and all codes and requirements 
of the authority having jurisdiction. Failure 
to follow instructions could result in serious
injury or property damage. The qualified
agency performing this work assumes
responsibility for the conversion.

CAUTION:

The following adjustments

must be made before turning on the burner.
Failure to do so could result in serious injury.
Be sure pressure regulator has been
converted as described in Step 2.

1

ADJUST YOUR COOKTOP FOR
USE WITH LP GAS

Disconnect all electrical power, at the
main circuit breaker or fuse box.

Shut off the gas supply to the cooktop 
by closing the manual shut-off valve.

Adjust the pressure regulator, by the
following instructions:

Unscrew the cap.

Place your thumb against the flat side
of the spring retainer and press down
to remove the retainer.

Carefully look at the spring retainer to
locate the NAT or LP position.

Turn the spring retainer over so that 
LP is showing on the bottom.

Snap the retainer back into position.

Screw the cap back onto the regulator.

C

B

A

2

DOWN 

FOR OFF

NAT

LP

LP

NAT

LP

NAT

NAT

LP

Gasket

Cap

Spring
Retainer

L.P./Propane
Position

NAT.

Position

Pressure Regulator

TOOLS YOU WILL NEED 
FOR LP CONVERSION

Safety Glasses

Small Flat-Head

Screwdriver (4mm

or 5/32

tip size,

60mm long)

Phillips Head

Screwdriver

Pliers

7mm Nutdriver

No. 15 Torx-Head

Driver

Summary of Contents for JGP630

































Reviews: