background image

Document 8600092587P   r04 2019 May

 

1

 

Integritas Wall Mount Charger 

-

 Quick Start Guide

 

 

 

Integritas

™ 

Wall Mount 3 Rectifier Battery Charger

 

 

Read and follow all safety statements, warnings, and precautions in this guide.

 

Basic Features:

 

All DC outputs are floating 

-

 not referenced to ground.

 

DC output Ground Fault Detection. Set at factory default adjustable at site, if necessary.

 

Monitored class II AC input surge device included in addition to surge capability of IP rectifier units.

 

Monitored Class III output surge device included.

 

Full

-

featured charger control unit.

 

GE

 

Critical Power

 

 

Quick Start Guide

 

Bottom Feed Charger with BATT & DC Load Breakers

 

Model number structure:  

3TL125

-

SACY

-

D10Y

-

P000

 

DC output 

options

 

Controller 

options

 

3 Rectifiers, Top/Bottom 

Feed,

 

AC input 

options

 

Top Feed Charger with 2 DC Breakers

 

Input Box 

 

Output Box

 

Wall 

Mount 

Bracket

 

(top and 

bottom)

 

IO Module 

 

IP Rectifier 

slots (3)

 

Air Filter

 

Door Latch

 

(Lock option)

 

Control 

Panel

 

DC Output 

Box

 

Chassis 

Ground 

Lug

 

Signal Wire 

Knockouts

 

(top and 

bottom)

 

Controller

 

IO Mod-

ule slot

 

Controller 

slot

 

Air Filter

 

IP Rectifier 

slots (3)

 

Door Latch

 

(Lock option)

 

Drip/Drop Shield

 

Output 

Signal Unit

 

Output 

Ground Fault 

Input 

Box 

 

Output 

Signal Unit

 

Output 

Ground Fault 

Summary of Contents for Integritas 3TL125-SACY-D10Y-P000

























Reviews: