GE IMP2B Hardware Reference Manual Download

Page: 29 / 55

Publication No. IMP2B-0HH/5

Functional Description 29

3.15.2

Board ID Register 1 – Offset 0x00000000

Table

3-10 Board ID Register 1

Bits

Mode

Description

Notes

7 to 0

Read only Board major revision

0x02=2BB

15 to 8

Read only Board identifier (0x4A) 0x4A = IMP2B

3.15.3

Board ID Register 2 – Offset 0x00000002

Table

3-11 Board ID Register 2

Bits

Mode

Description

Notes

7 to 0

Read only CPLD revision

0x01 = Rev 01

15 to 8

Read only Board minor revision 0x00=Rev A, 0x01=Rev B, etc

3.15.4

Device/Bus Information Register 1 – Offset 0x00000004

Table

3-12 Device/Bus Information Register 1

Bits

Mode

Description

Notes

2 to 0

Read only CompactPCI bus speed 000 = PCI @ 33 MHz

001 = PCI @ 66 MHz

Reserved

6 to 4

Read only PMC bus speed

000 = PCI @ 33 MHz
001 = PCI @ 66 MHz
100 = PCI-X @ 66 MHz
101 = Reserved
110 = PCI-X @ 133 MHz

Read only PMC I/O voltage

0 = 3.3 V (hardwired)

9 & 8

Read only Flash device size

00 = 1 Gbit
01 = 2 Gbit (planned)
10 = Reserved
11 = 512 Mbit

Read only Flash banks fitted

0 = 1 bank fitted
1 = 2 banks fitted (default)

Read only Flash type

0 = Spansion Flash fitted (hardwired)

13 & 12

Read only DRAM device size

00 = Reserved
01 = Reserved
10 = 1 Gbit
11 = Reserved

Read only DRAM Bank 1 fitted

0 = Not fitted
1 = Fitted

Reserved

Summary of Contents for IMP2B
























































Search results

Summary of Contents for IMP2B

Reviews:

Related manuals for IMP2B

Brands by name

Popular brands

GE IMP2B, Hardware Reference Manual

Search results

Summary of Contents for IMP2B

Reviews:

Related manuals for IMP2B

Brands by name

Popular brands