GE IMP2B Hardware Reference Manual Download | Manualshive

Page: 21 / 55

background image

Publication No. IMP2B-0HH/5

Functional Description 21

3.6 Memory Map set up by VxWorks (as seen by CPU)

Table 3-4 VxWorks Card-level Memory Map

Size

Function

Range

512 MBytes

SDRAM Bank 0

0x0000 0000 to 0x1FFF FFFF

512 MBytes

SDRAM Bank 1 (If fitted)

0x2000 0000 to 0x3FFF FFFF

128 MBytes

DEV_CS0 Flash Bank 1 (if fitted) 0x7000 0000 to 0x73FF FFFF

128 MBytes

DEV_CS3 Flash Bank 0

0x7400 0000 to 0x77FF FFFF
(0x7000 0000 to 0x73FF FFFF if Flash Bank 1 not fitted)

512 MBytes

CompactPCI memory

0x8000 0000 to 0x9FFF FFFF

256 MBytes

PMC memory

0xC000 0000 to 0xCFFF FFFF

16 MBytes

DEV_CS1 (EPLD registers)

0xE200 0000 to 0xE200 FFFF

16 MBytes

DEV_CS2 (NVRAM)

0xE300 0000 to 0xE3FF FFFF

4 MBytes

PMC I/O space

0xFE00 0000 to 0xFE3F FFFF

4 MBytes

CompactPCI I/O space

0xFE40 0000 to 0xFE7F FFFF

64 KBytes

Discovery V registers

0xFEF0 0000 to 0xFEF0 FFFF

8 MBytes

DEV_CSBOOT (Boot Flash)

0xFF80 0000 to 0xFFFF FFFF

3.7 PMC Site

The PMC site is connected to the PCI0 port of the MV64560. This bus supports 32- or
64-bit data widths and bus speeds up to 133 MHz. It is capable of using the PCI-X
protocol, but is backward compatible with standard PCI. The PMC bus speed can be
read from the EPLD

Device/Bus Information Register 1

.

Only PMC cards that operate using 3.3 Volt signaling (VIO) are supported.

CAUTION

Fitting a PMC designed to operate at 5 Volts VIO may cause damage to the IMP2B and/or PMC

The PMC site supports Processor PMCs (as defined by VITA32-2002) operating in
non-Monarch mode only.

CAUTION

The second bank of DDR2 memory occupies the PMC ‘keep-out’ area, which reduces the maximum

component height on a PMC from 10mm to 5mm in this area. When the second DDR2 bank is not

fitted, the full 10mm PMC component height is available.

The four interrupts from the PMC site are wired together and routed to the interrupt
handler in the MV64560.

The MV64560 provides the PCI arbiter for the bus and supports two bus masters on
the PMC card.

Table 3-5 PMC Site IDSEL Connections

IDSEL Function
24

PMC Device A

25

PMC Device B

«
...
19
20
21
22
23
...
»

Summary of Contents for IMP2B
























































Reviews:

No comments

Related manuals for IMP2B

Brand: Qiyang Pages: 72

Brand: IEI Technology Pages: 17

Brand: Fastwel Pages: 61

P3000BX2 Series

Brand: RadiSys Pages: 64

PROTEUS-1.33-M1G-F2G-GPS-I

Brand: Eurotech Pages: 74

VSBC-6872 Series

Brand: Actis Pages: 105

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands