GE iBox Installation And Maintenance Manual Download Page 131

Page: 131 / 172

GE Grid Solutions

iBox/iBox Kit

Installation and Maintenance Guide

GE Information

994-0047-5.10-4

131

Testing the iBox Kit

Overview

You can verify the iBox Kit is operating properly by:

•

Inspecting the LEDs on each of the iBox Kit components, and

•

Pinging the Ethernet Module and the iBox from your PC

Digi One IAP

LEDs

When operating normally, the Digi One LEDs appear as follows:

LED

Normal Operation

POWER

Solid GREEN

LINK

Solid GREEN

DCD

Solid GREEN

DSR

Solid GREEN

DTR

Solid GREEN

RTS

Solid GREEN

Flashing GREEN

ADAM-4017+

LEDs

The ADAM-4017+ has a single GREEN LED, which operates as follows:

LED Operation

Description

OFF

Power OFF

GREEN Solid

Power ON, unit is not being polled over the

Modbus interface.

GREEN Flashing

Power ON, unit is being polled over the Modbus

interface at the same rate as the LED is flashing.

DMMS LEDs

Refer to the manufacturer’s manual.

iBox LEDs

For information on iBox LED operation, refer to:

•

“LEDs” on page 32 (for LED operation during self diagnostics)

•

“LED Descriptions” on page 46 (for normal LED operation)

•

“Errors Indicated by LEDs” on page 74 (for information on using LED

indications to troubleshoot iBox problems)

Pinging the

Ethernet and

iBox

If the iBox Kit modules are operating correctly, and it is configured for LAN

connection, you will be able to ping the Ethernet Module and iBox IP addresses from

your PC.

Summary of Contents for iBox













































































































































































Search results

Summary of Contents for iBox

Reviews:

Related manuals for iBox

Brands by name

Popular brands

GE iBox, Installation And Maintenance Manual

Search results

Summary of Contents for iBox

Reviews:

Related manuals for iBox

Brands by name

Popular brands