GE H49021AA Basic Service Manual Download Page 375

Page: 375 / 420

GE M

EDICAL

YSTEMS

IRECTION

5184024-100, R

EVISION

LOGIQ

WORKS

ASIC

ERVICE

ANUAL

Chapter 8 Replacement Procedures

8-13

8-2-6

Cable Replacement Procedure

8-2-6-1

Preparations

•

Shut Down and turn Off the Workstation and all its parts as described.

8-2-6-2

Cable Removal

1.) Unplug the cable from the connecting devices.

2.) Remove the cable.

8-2-6-3

Cable Installation

1.) Plug the New Cable to the same devices as the old one was connected to.

2.) Turn on the workstation and the connected device.

a.) Power Cable: Verify System is powered on.

b.) Fire wire Cable: Insert a media into the DVD Drive. Connect to the Dataflow, and verify there

is power on the DVD drive and that you are able to read from the disk.

c.) Ethernet Cables: Verify a green link light present on the Ethernet Switch, or PC.

d.) RS-232 Cable, modem: Verify iLinq connection.

CAUTION

This procedure is a general cable replacement procedure, and should be valid for Power, Fire wire,
Ethernet and RS-232 cables.

Summary of Contents for H49021AA





































































































































































































































































































































































































































Search results

Summary of Contents for H49021AA

Reviews:

Related manuals for H49021AA

Brands by name

Popular brands

GE H49021AA, Basic Service Manual

Search results

Summary of Contents for H49021AA

Reviews:

Related manuals for H49021AA

Brands by name

Popular brands