background image

Listed by 

Underwriters 

Laboratories

For answers to your Monogram, GE Café

 Series, GE Profile

 Series or 

GE Appliances product questions, visit our website at geappliances.com 
or call GE Answer Center

®

 Service, 800.626.2000.

GUD27ESSM/27GSSM 

GE

®

 Unitized Spacemaker

®

 3.8 DOE Cu. Ft. Stainless Steel Washer and 5.9 Cu. Ft. Dryer

DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES) 

Specification Revised 11/17

ELECTRICAL REQUIREMENTS: 

 

GUD27ESSM Electric Dryer – This appliance should be connected to an 
individual, properly-grounded branch circuit with 120/240V or 120/208V 

single-phase 60 Hz electrical service and should be protected by  

30-amp time-delay fuses or circuit breakers KW Rating per voltage 

(240/208). This appliance is manufactured with neutral connected to  
the frame. Power cord should be purchased separately.

GAS REQUIREMENTS:

 

GUD27GSSM Gas Dryer – This appliance should be connected to an 
individual branch circuit with 120-volt single-phase 60 Hz electrical 
service and should be protected by 20-amp time-day fuses or circuit 
breakers. This appliance is equipped with a 4-foot long flexible U.S.  
listed 20-amp power cord to match a 20-amp receptacle.

NOTE:

 Gas Rated input 20,000 BTU/HR. Factory equipped for natural 

gas. Tested for LP gas. LP gas supply requires a conversion kit. Have a 
qualified gas technician install a conversion kit before use.  
Dryers must be exhausted to the outside.

INSTALLATION INFORMATION: 

For complete information, see 

installation instructions packed with the product.

Installation Instructions

* Dimension represents door closed including handle and knobs.

NOTE: With feet set at mid position, feet can be ad/- 3/8".

27" NOMINAL PRODUCT DIMENSIONS

Vent

Drain outlet 

51°

Gas Inlet

Water Inlets 

*26-1/8"

34-3/8"

4-3/8"

3"

47 1/2"

18-5/8"

12-1/2"

75-7/8"

53-1/4"

3-7/8"

36-7/8"

30-7/8"

26-3/4"

22-1/4"

3"

Summary of Contents for GUD27ESSM

Page 1: ...rately GAS REQUIREMENTS GUD27GSSM Gas Dryer This appliance should be connected to an individual branch circuit with 120 volt single phase 60 Hz electrical service and should be protected by 20 amp time day fuses or circuit breakers This appliance is equipped with a 4 foot long flexible U S listed 20 amp power cord to match a 20 amp receptacle NOTE Gas Rated input 20 000 BTU HR Factory equipped for...

Page 2: ...etal semi rigid ducting cannot be used AND where a 4 diameter can be maintained throughout the entire length of the transition duct Please see installation instruction packed with your dryer for complete instructions when using flexible metal foil type ducting EXHAUST LENGTH CALCULATION 1 Determine the number of 90 turns needed for your installation If you exhaust to the side or bottom of dryer ad...

Page 3: ... or closet it will be stated on a label on the dryer back The dryer MUST be exhausted to the outside Minimum clearances between dryer cabinet and adjacent walls or other surfaces are 0 both sides and rear 1 front and top Minimum vertical space from floor to overhead cabinets ceilings etc is 76 1 2 Closet doors must be louvered or otherwise ventilated and must contain a minimum of 60 sq in of open ...

Page 4: ...sh spin speed combinations Speeds are matched to fabric type for great clothes care Auto load sensing with 4 water levels Washer will automatically measure the load size and add just the right amount of water Rotary electronic controls washer Simplify cycle selection Bleach and fabric softener dispensers Solutions are automatically mixed with wash water for clean bright soft to the touch results C...

Reviews: