15
SPECIFICATIONS/DIMENSIONS
Installation Instructions
These systems conform to WQA NSF/ANSI 44 for the specific capacity claims as verified and substantiated by test data.
*
Testing was performed using pellet grade sodium chloride as the regenerant salt.
**
Efficiency rating is valid only at the lowest stated salt dosage. These softeners were efficiency rated according to
WQA NSF/ANSI 44.
***
Extent of iron removal may vary with conditions. The capacity to reduce clear water iron is substantiated by WQA
test data. State of Wisconsin requires additional treatment if water supply contains greater than 5 ppm clear water
iron. Use of Diamond Crystal
®
Red•Out
®
or Super Iron Out
®
will improve iron removal. Refer to
Cleaning Iron Out
of the Water Softening System
section.
SANITIZING PROCEDURES
To complete the installation, do the following
sanitizing procedures.
Care is taken at the factory to keep your water
softener clean and sanitary. Materials used to make
the softener will not infect or contaminate your water
supply and will not cause bacteria to form or grow.
However, during shipping, storage, installation and
operation, bacteria could get into the softener. For
this reason, sanitizing as follows is suggested when
installing.
NOTE: Sanitizing is recommended by the
Water Quality Association for disinfecting.
1.
Be sure to complete all installation steps, including
programming the control.
2.
Pour about 3/4 oz. (1
1
⁄
2
tablespoons) of common
5.25% unscented household bleach (Clorox, Linco,
Bo Peep, White Sail, Eagle, etc.) into the
brinewell
.
Refer to illustration on page 5.
3. IMPORTANT:
Press and hold for 3 seconds the
faceplate
REGEN
button to start an immediate
regeneration. The indicator light will alternate
between TIME OF DAY and REGEN TIME
REMAINING. The bleach will be drawn
through the water softener, and out the drain.
This process takes approximately 3 hours.
4.
If, after sanitization, water from the house
faucet tastes salty or has a slight color, this is a
preservative from the resin tank. Turn on the cold
soft water faucets and drain for a few minutes or
until clear.
NOTE
:
When the sanitizing regeneration is over,
all remaining bleach is flushed from the conditioner
and your house
COLD
water supply is fully soft
immediately. However, your water heater is filled
with hard water and as hot water is used, it will refill
with soft water. When all the hard water is replaced
in the water heater, hot only and mixed hot and cold
water will be fully soft. If you want totally soft water
immediately, after the above regeneration, drain the
water heater until the water runs cold.
WARNING:
If you do drain the water
heater, use extreme care as the hot water could
cause burns. Turn the water heater off prior to
draining.
GNPR40L
GNPR48L
Resin Tank Size
10x44
″
12x48
″
Resin Volume
1.25 ft
3
1.50 ft
3
Refill Controller
0.35 gpm
0.35 gpm
Backwash Controller
2.8 gpm
2.8 gpm
Brine Tank
Size
15x40
″
15x40
″
Capacity
350 lbs
350 lbs
Operation Temperature
Min.
34°
34°
Max.
100°F
100°F
Flow Rate
15.2 gpm
18.0 gpm
Pressure Drop
15.0 psi
15.0 psi
Maximum Flow to Drain
4.0 gpm
3.5 gpm
CL
47
″
40
1
⁄
4
″
15
″
10
″
14
1
⁄
2
″
44
40
1
⁄
4
″
15
″
51
1
⁄
4
″
CL
12
″
15
1
⁄
4
″
48
50
″
54
1
⁄
4
″
