Consumer
S
uppor
t
Tr
oubleshooting
Tips
Operating
Instructions
Safety
Instructions
SPEED CYCLE
7.3 gal., 35 min.
or
This cycle is for everyday dishes and glassware.
SPEED WASH
(on some models)
CHINA CRYSTAL
7.3 gal., 48 min.
(on some models) This cycle is for lightly soiled china and crystal.
RINSE ONLY
2.5 gal., 12 min.
For rinsing partial loads that will be washed later. Do not use detergent with this cycle.
NOTE:
Only the Anti-Bacteria cycle has been designed to meet the requirements of Section 6, NSF 184 for
soil removal and sanitization efficacy
.
Options
The light above the selected pad will be
ON
to indicate which option has been selected.
PRE SCRUB
For use with heavily soiled and/or dried-on, baked-on soils. This option
MUST
be selected
PRIOR
to
(on some models) starting the cycle.
This option adds 16 minutes to the cycle time.
NOTE:
Cannot be selected with
RINSE ONLY
cycle.
HEATED DRY
Shuts off the drying heat option. Dishes air dry naturally and energy is saved. For faster air dry,
Light OFF
you can prop the door open after the
CLEAN
light illuminates.
HEATED DRY
Turns the heater on for fast drying. This will extend the total run time by 8 minutes for the
SPEED
Light ON
CYCLE
, 38 minutes for
NORMAL
and
POTS/PANS
, and 30 minutes for all other cycles.
NOTE:
Cannot be selected with
RINSE ONLY
cycle.
LOCK
You can lock the controls to prevent any selections from being made. Or you can lock the controls
after you have started a cycle.
Children cannot accidentally start dishwasher by touching pads with this option selected.
To LOCK the dishwasher control,
touch and hold the
HEATED DRY
pad for 3 seconds. The light
below the
HEATED DRY
pad will turn on.
To UNLOCK the dishwasher control,
touch and hold the
HEATED DRY
pad for 3 seconds. The
LOCK
light will turn off.
ADDED
When selected, the cycle will run longer with the heating element on to improve both wash and
HEAT
dry performance.
NOTE:
Cannot be selected with
RINSE ONLY
cycle.
DELAY HOURS
You can delay the start of a wash cycle for up to 9 hours. Touch the
DELAY HOURS
pad to choose
the number of hours you want to delay the start of the cycle; then touch
START/RESET
one time.
The dishwasher will count down and start automatically at the correct time.
Touching
START/RESET
a second time will cancel the
DELAY START
selection
.
RESET
To change a cycle after washing starts, touch the
START/RESET
pad to cancel the cycle. The
START/RESET
light will flash while the water is pumped out if needed. This takes approximately
90 seconds. When the light stops flashing, the dishwasher can be reprogrammed and restarted.
Start
Close and latch the dishwasher door and select the cycle and desired enhancements. Touch the
START/RESET
pad
once to begin the cycle. Water begins to fill the dishwasher, and approximately 60 seconds later the wash action
begins. Touching the
START/RESET
pad a second time will cancel the cycle and cause the water to drain out. This will
take approximately 2 minutes.
NOTE:
The dishwasher remembers your last cycle so you don’t have to reprogram each time. When the dishwasher
door is fully closed, the control panel lights will display the last settings you selected.
If you don’t want to change any of the settings, simply touch the
START/RESET
pad once to begin the cycle.
If the door is closed, the indicator lights will turn off if the
START/RESET
pad is not pressed within two minutes.
To activate the display, open and close the door or touch any pad.
Also, if a power failure occurs,
NORMAL
and
HEATED DRY
will automatically be programmed.
4
ge.com
5
5