7
Co
ns
um
er
S
up
po
rt
Tro
ub
les
ho
ot
in
g T
ip
s
O
pe
ra
tin
g I
ns
tru
cti
on
s
Sa
fe
ty
In
str
uc
tio
ns
GEAppliances.com
Options
The light above the selected pad will be
On
to indicate which
OpTIOn
has been selected.
HOT START/
For use with heavily soiled and/or dried-on, baked-on soils. This option
MuST
be
STEAM
selected
prIOr
to starting the cycle.
This option will improve both wash and dry
(on some
performance. This option adds 20 minutes to the cycle time.
models)
nOTE:
Cannot be selected with
rInSE Only
cycle.
HEATED DRY
Shuts off the drying heat option. Dishes air dry naturally and energy is saved.
light oFF
For faster air dry you can prop the door open after the
ClEAn
light illuminates.
HEATED DRY
Turns the heater on for fast drying. This will extend the total run time by 38 minutes.
light on
nOTE:
Cannot be selected with
rInSE Only
cycle.
LOCK
You can lock the controls to prevent any selections from being made. or you can lock
the controls after you have started a cycle.
(on some
children cannot accidentally start dishwasher by touching pads with this option
models)
selected.
To LOCK the dishwasher control,
touch and hold the
HEATEd dry
pad for 3 seconds. The light below
the
HEATEd dry
pad will turn on.
To UNLOCK the dishwasher control,
touch and hold the
HEATEd
dry
pad for 3 seconds. The
lOCK
light will turn off.
HOT WASH/
When selected, the cycle will run longer with the heating element on to improve both
ADDED HEAT
wash and dry performance. For use with heavily soiled and/or dried-on soils. This
option
MuST
be selected
prIOr
to starting the cycle.
nOTE:
Cannot be selected with
rInSE Only
cycle.
DELAY HOURS
You can delay the start of a wash cycle for 2, 4 or 8 hours (delay time options may vary
by model). Touch the
dElAy HOurS
pad to choose the number of hours you want to
delay the start of the cycle; then touch
STArT/rESET
one time. The dishwasher will
count down and start automatically at the correct time.
Touching
STArT/rESET
a
second time will cancel the
dElAy STArT
selection
.
RESET
To change a cycle after washing starts, touch the
STArT/rESET
pad to cancel the
cycle. For some models, the
lEd
’s indicating selected cycle and options will flash while
the water is pumped out. This takes approximately 105 seconds. When the lights stops
flashing, the dishwasher can be reprogrammed and restarted. Buttons will not respond
during pump out.
For other models, the
lEd
’s indicating the selected cycle and options will flash and the
drain pump will pump water out of the dishwasher for 105 seconds and then turn off.
Buttons will respond during pump out. If any button is pressed during the pump out,
the
lEd
’s will stop flashing and indicate new cycle or options selected. If the
STArT/rESET
button is pressed while the dishwasher is in pump out, the dishwasher
will start a new wash cycle.
Start
Close and latch the dishwasher door and select the cycle and desired enhancements.
Touch the
STArT/rESET
pad once to begin the cycle. Water begins to fill the
dishwasher, and approximately 60 seconds later the wash action begins.
nOTE:
The dishwasher remembers your last cycle so you don’t have to reprogram each
time. When the dishwasher door is fully closed, the control panel lights will display the
last settings you selected.
If you don’t want to change any of the settings, simply touch the
STArT/rESET
pad
once to begin the cycle.
If the door is closed, the indicator lights will turn off if the
STArT/rESET
pad is not
pressed within two minutes. To activate the display, open and close the door or touch
any pad.
Also, if a power failure occurs,
nOrMAl WASH
and
HEATEd dry
will automatically be
programmed.
3
4
