STEP 18: PRETEST CHECKLIST
Review this list after installing your dishwasher to avoid
charges for a service call that is not covered by your
warranty.
• Check to be sure power is OFF.
• Open door and remove all foam and paper packaging.
• Locate the Owner’s Manual set aside in Step 1.
• Read the Owner’s Manual for operating instructions.
• Check door opening and closing. If door does not open and
close freely, check for proper routing of spring cable over
SXOOH\,IGRRUGURSVRUFORVHVZKHQUHOHDVHGDGMXVWVSULQJ
tension. See Step 2.
• Check to be sure that wiring is secure under the dishwasher,
not pinched or in contact with door springs or other
components. See Step 17.
• Check door alignment with tub. If door hits tub, level
dishwasher. See Step 13.
• Pull lower rack out, about halfway. Check to be sure it does
QRWUROOEDFNRUIRUZDUGRQWKHGRRU,IWKHUDFNPRYHVDGMXVW
leveling legs. See Step 13.
• Check door alignment with cabinet. If door hits cabinet,
reposition dishwasher. See Step 12.
• Check that door spring does not contact water line, fill hose,
wiring or other components. See Step 12.
• Verify water supply and drain lines are not kinked or in
contact with other components. Contact with motor or
dishwasher frame could cause noise.
• Turn on the sink hot water faucet and verify water
temperature. Incoming water temperature must be between
120°F and 140°F. A minimum of 120°F temperature is
required for best wash performance. See “Prepare Hot Water
Line,” page 5.
• Add 2 quarts of water to the bottom of the dishwasher to
lubricate the pump seal.
• Turn on water supply. Check for leaks. Tighten connections if
needed.
• Remove protective film if present from the control panel and
door.
• Check that tub trim does not contact the door.
Dishwasher Installation
13
STEP 17: CONNECT POWER SUPPLY
If a power cord with plug is already installed proceed to
Step 18.
,QWKLVVWHS\RXZLOOQHHGWKHMXQFWLRQER[FRYHUDQGWKH
#10 Hex head screw from the screws set aside in Step 1.
6HFXUHKRXVHZLULQJWRWKHEDFNRIWKHMXQFWLRQER[ZLWKD
strain relief.
• Locate the 3 dishwasher wires, (white, black and green) with
WKHVWULSSHGHQGVFRPLQJRXWRIWKH$&MXPSHU8VH8/OLVWHG
wire nuts of appropriate size to connect incoming ground to
green, white to white and black to black.
,QVWDOOWKHMXQFWLRQER[FRYHUXVLQJKH[KHDGVFUHZ
Check to be sure that wires are not pinched under the cover.
0DNHVXUHWKDWWKHMXQFWLRQER[FRYHULVUHVWLQJRQWKH
mounting bracket.
WARNING:
If house wiring is not 2-wire with ground, a ground must be
provided by the installer. When house wiring is aluminum, be sure
to use UL-Listed anti-oxidant compound and aluminum-to-copper
connectors.
Figure AA
Ground
(Green)
NOTE: Do not remove the
Junction Box Bracket.
AC
Jumper
Junction Box
Bracket
Black
White
ADVERTENCIA:
Si el cableado doméstico no cuenta con un cable de 2 hilos con
conexión a tierra, un instalador debe realizar una conexión a tierra.
Cuando el cableado doméstico es de aluminio, asegúrese de usar
un compuesto antioxidante y conectores de aluminio a cobre
aprobados por UL.
Ground
Screw
NOTE:
All ground screws, brackets and wires must remain
intact.
