GE G017, Owner'S Manual, Page: 4 / 64

Throughout this manual, features and appearance may vary from your model.
4
Operating instructions.
Controls
A
B
Power
Press to “wake up” the display. If the display is active, press to put the washer into idle mode.
NOTE: Pressing Power does not disconnect the appliance from the power supply.
Start and Unlock Lid
Press Start to begin the cycle. NOTE: The lid must be closed for the washer to fill and the cycle to start. If the lid is open, “LID” will scroll across
the display. If the lid is closed, the lid will lock, the LID LOCKED light will light, the detergent will be dispensed, and “FILL” will scroll across the
display.
Pressing
Unlock Lid will Pause the cycle and the Start indicator light will blink.
To continue the cycle, press Start again. If machine is paused more than 24 hours, the cycle will be cancelled. If water remains in the machine,
select the Drain & Spin cycle to drain basket and spin water out of the washer basket.
Display and Status Lights
Display: The display shows the approximate time remaining until the end of the cycle.
NOTE: The cycle time is affected by how long it takes the washer to fill. This depends on the water pressure in your home. The “smart” timer
“learns” the amount of time it takes to fill your washer and adjusts the total time accordingly.
In addition, this display will, “scroll” the washer status:
• bALAnCINg Start of rebalancing cycle to redistribute clothes. Stops after rebalancing is complete.
• CyCLE PrEP Sensing dry load size prior to fill (normal).
• dELAY When Delay Wash is initiated. Replaced with estimated time when cycle starts.
• End End of current cycle.
• FILL For the first 45 seconds of a fill, the estimated end of cycle time is displayed. For the rest of the fill time, “FILL” is scrolled
until the fill completes.
• H2O SUPPLY Can not sense water level (valves possibly turned off).
• LId Cycle stopped because lid is open. Close the lid.
• LOAd SEnSE Sensing wet load size (normal).
• PAUSE Cycle paused because the Start / Pause button was pressed and the washer was set to Pause . Press Start button again to
restart the cycle.
Cycle status lights: Shows whether the washer is in the SOAK, WASH, RINSE or SPIN cycle.
If an out-of-balance condition is detected by the washer, the Spin light will blink during the remaining portion of the cycle and will stay
illuminated for a short time after cycle completion. When this occurs, the washer is taking actions to correct the out-of-balance condition
and complete the cycle normally. In some cases, the washer may not be able to balance the load and spin up to full speed. If you notice the
load is more wet than normal at the end of the cycle, redistribute the load evenly in the wash basket and run a Drain & Spin cycle.
Feature status lights indicate (see sections F and G for more details) :
Lid Locked - The lid is locked. See the Control Lock description.
Locked Controls - Will blink once if you press any button or turn the cycle knob.
- Washer is connected to the network and can communicate with a connected smartphone device.
Delay Wash - A delay wash time is set.
C
• Loosely add items around infusor.
Overloading may negatively impact
wash performance. See page 11 for
suggested loading examples.
• Close lid.
NOTE : Washer will not fill with lid
open.
Step 2
Step 3
Step 4
Step 1
• Select wash cycle.
• Select wash options,
including Deep Rinse option
when using fabric softener.
• Select options including
Pretreat/Bleach option.
• Press Start.
D C G B
A F
E
H
• Add fabric softener to the fabric
softener dispenser; see page 7.
• Add detergent. GE recommends
the use of High Efficiency
detergents such as
in your
energy efficient washer.