background image

INTRODUCTION

Your Telephone is designed to give you flexibility in use, and high 

quality performance. To get the most from your new telephone, we 

suggest that you take a few minutes right now to read through this 

instruction manual.

If you have any questions or problems, consult the Troubleshooting 
Tips for the solution.

PAPTS CHECKLIST

Your package should contain the following items:

BEFORE YOU BEGIN

MODULAR JACK REQUIREMENTS

You need an RJ11C type modular jack, which is 
the most common type of phone jack and might 
look like the one pictured here. If you don’t have 
a modular jack, call your local phone company 
to find out how to get one installed.

INSTALLING THE PHONE

Your telephone should be placed on a level surface such as a desk top, 
or you can mount it on a wall , A desktop /wall mounting pedestal is built 
into the base of the phone.

Connect the telephone line cord to a modular telephone jack.
Slide the RINGER switch (on the handset ) to Low or High.
Set PULSE/ TONE switch (on the handset ) to TONE for touch-tone 
service, or set it to PULSE for rotary service. If you don’t know which 
type of service you have, check with the phone company.

1.
2.
3.

WALL MOUNT INSTALLATION

Your telephone may also be mounted on a wall plate (not  included).

Slip the mounting holes (on the bottom 
of the base) over the wall plate posts and 
firmly slide the unit down into place.
Plug the telephone line cord into a 
modular wall phone jack.

1.

2.

USING THE TELEPHONE FEATURES

RECEIVING A PHONE CALL

Be sure the RINGER switch is set to Hi (       ) or Lo (    ) position.
When the phone rings. lift the handset and begin your conversation.
After 5 sec, a talk timer will be displayed.
Slide the RINGER switch to the Off (       ) position when you do not want 
to be interrupted by the phone ringing.

1.
2.
3.
4.

RINGER VOLUME

You may control the ringer volume level with the switch located on the 
right side of the handset.
      = ringer tone will be loud.

      

= ringer tone will be low.

      = telephone will not ring.

PLACING A PHONE CALL

1.  Lift the handset and wait for a dial tone.
2.  Dial the telephone number you wish to call,
     while the LCD displays ‘Ξ’.
3.  After 5 sec, a talk timer will be displayed.

TEMPORARY TONE FEATURE

If you have Pulse ( rotary ) service and want to access 

customer calling services that require  touch –tone 

dialing ,such as getting information from a local bank 

,you can use this feature.

Press the TONE button ( * ) after you have connected 

to the service in order to enable touch –tone dialing. 

When you hang up, the phone automatically returns 
to Pulse dialing mode.

1.

2.

TROUBLESHOOTING TIPS

PROBLEM                                                              SOLUTION

No dial tone 
Won’t dial out

Check hook switch to make sure it pops up.

Make sure TONE / PULSE is set to correct position.

Phone doesn’t ring

Make sure RINGER switch is set to Hi (     ) or Lo(     )

You might have too many phones on one line.

Feedback when 
dialing in PULSE mode

This is normal, power fluctuates with phone 
outpulsing.

Can’t be heard by 
other party

Make sure phone cord is securely plugged in.

Make sure other phones aren’t off the hook 

at the same time you ’ re using the phone.

It is normal for the  volume to drop when 

additional phones are used at the same time.

CARE AND MAINTENANCE

T

o keep your phone working and looking good ,follow these guidelines;

Avoid putting near heating appliances and devices that generate 

electrical noise (for example , motors and fluorescent lamps)

DO NOT expose to direct sunlight or moisture.

Avoid dropping and other rough treatment of the unit.

Never use a strong cleaning agent or abrasive powder because this 

will damage the finish.

Retain the original package in case you need to ship it at a later date.

Used equipment must be disposed of in compliance with 

current environmental protection regulations. You should 

return it to your reseller or dispose of it in an approved 

recycling centre.

Model EX29268

00022382 (Rev.0 E/S)

07-39

Printed in China

Thomson Asia Limited 
3/F., Delta House, 3 On Yiu Street,
Siu Lek Yuen, Shatin, Hong Kong

is a trademark of General Electric Company and is under license by Thomson Asia Ltd., Hong Kong

www.thomson-asia.com.hk

Wall plate

Telephone

line jack

REDIAL BUTTON

This unit redials up to 32 digits. To 

automatically redial the last number You 

called: 

1. Pick up the handset to get a dial tone.

2. Press redial.

3. LCD shows the phone number you dialed.

MEMORY

Each of the memory buttons is capable of storing phone numbers that 

are up to 32 digits. Memory locations 0-9 require you to press MEM
for access.

STORING A NUMBER IN MEMORY

1. Pick up the handset.

2. Press ths STORE button.

3. Dial the number to be stored (up to 32 digits), 

    LCD show the phone number.

4. Press STORE again.

5. Press a memory location button(0-9)

6. Record the telephone number you want to store.

7. Hang up the handset.

DIALING A NUMBER FROM MEMORY

You can dial numbers from memory when using the handset. When you 

get a dial tone, press the MEM button followed by the memory location 

(0-9) for the number you want to dial.

INSERTING A P AUSE IN THE DIALING SEQUENCE 

Use the REDIAL button to add pauses to a dialing sequence, for example 
after you dial 9 for an outside line.

1234567890

29268

Telephone 

User’s Guide

Base unit with handset

Store

Mem

Redial

Tone/Pulse

Switch

Ringer

Hi/Lo/off

TONE button

Reviews: