background image

Druck DPI 142/150 Calibration Manual

iii

    K382 Issue No. 1

Glossary

Terminology

The terminology used in this manual is specific and individual interpretation 
must not be introduced.  The terms are defined as follows:

Adjust

To bring to a more satisfactory state; to manipulate controls, 
levers, linkages, etc. to return equipment from an out-of-tolerance 
condition to an in-tolerance condition.

Align

To bring into line; to line up; to bring into precise adjustment, 
correct relative position or coincidence.

Calibrate:

To determine accuracy, deviation or variation by special 
measurement or by comparison with a standard.

Check:

Make a comparison of a measure of time, pressure, temperature, 
resistance, dimension or other quality with a known figure for that 
measurement.

Disconnect: To detach the connection between; to separate keyed or matched 

equipment parts.

Examine:

To perform a critical visual observation or check for specific 
conditions; to test the condition of.

Inspect:

Review the work carried out by Specialists to ensure it has been 
performed satisfactorily.

Maintain:

To hold or keep in any particular state or condition especially in a 
state of efficiency or validity.

Operate:

Make sure that an item or system functions correctly as far as 
possible without the use of test equipment or reference to 
measurement.

Readjust:

To adjust again; to move back to a specified condition; to bring 
back to an in-tolerance condition.

Reconnect: To rejoin or refasten that which has been separated.

Reset:

To put back into a desired position, adjustment or condition.

Summary of Contents for Druck DPI 150














Reviews: