GE Digital Energy LP 33 Series Installation Manual Download Page 14 | Manualshive

Page: 14 / 38

GE Digital Energy LP 33 Series Installation Manual Download Page 14

Digital Energy™

g

OPM_LPS_3UI_10K_20K_0US_V010.doc

14/38

Installation Guide

LP 33

/ 10 - 20 kVA

3.3.2

Storage of the battery

In case of extended storage, when the delivery includes maintenance free batteries, keep in mind
that

they are subject to auto-discharging process

To avoid permanent damages to the battery, you must observe the following instructions:

•

The storage time without charging the battery depends on the temperature of the storage
ambient.

•

The optimal ambient temperature for the batteries is

68°F

(20°C).

For storage temperature higher than

68°F

(20°C), the storage time will decrease.

•

Each additional

18°F

(10°C) over the nominal temperature of

68°F

(20°C) will decrease the

storage time, without freshening charge, by half.

In case of a

maintenance free battery

, the storage time without charging the

battery

is

approximately:

6 months with storage temperature 68°F (20°C)

3 months with storage temperature 86°F (30°C)

2 months with storage temperature 95°F (35°C)

NOTE !
In case of

battery

storage pay

attention to:

FRAGILE

SENSITIVE

TO DAMPNESS

TO HEAT

SENSITIVE

TO FROST

SENSITIVE

«
...
12
13
14
15
16
...
»

Summary of Contents for Digital Energy LP 33 Series







































Reviews:

No comments