background image

GE Grid Solutions

 

D20/D200 Technical Overview

 

 

GE Information 

 

 

PRPI-019-3.00-10 

37

 

 

2.4  I/O Peripheral Modules 

The D20/D200 design is based on a distributed-processing architecture. As a result, the real-time 
data acquisition and control software that interfaces with field points is installed on peripheral 
modules, rather than on the main processor unit.  

These I/O peripherals are intelligent modules that contain on-board microprocessors. They are 
configured as slaves to the D20/D200 main processor. In this way, specific I/O processing is 
distributed throughout the RTU to the appropriate I/O module. 

D20 I/O peripherals communicate with the D20/D200 through a high speed, high-level data link 
controller (D.20 Link) in the form of poll and response messages. The peripheral modules have a 
serial communications port and a variable number of field connections. 

The hardware construction of each module is similar (see Figure 18.) Each peripheral module 
has common code stored in EPROM and a unique application configuration stored in RAM. The 
base application code is stored on the D20/D200. At power up, the configuration and application 
code are downloaded to the peripheral module from the D20/D200 main processor. 

2.4.1  Types of I/O Peripherals 

There are five basic types of I/O peripheral modules: 

 

D20S digital input 

 

D20A analog input 

 

D20K control output 

 

D20C combination input/output 

 

D20AC direct AC analog input 

I/O peripheral modules are available with a variety of I/O point count support and termination 
options. The following is a listing of the various D20 I/O peripherals that are currently available 
from GE Grid Solutions: 

Table 6  D20/D200 I/O Peripherals 

Peripheral 

I/O Support 

Termination 

D20A 

32 analog inputs, standard version 

Compression 

D20AD 

32 analog inputs, standard version 

DB25 

D20AX 

32 analog inputs, standard version 

Disconnect 

D20AB 

32 analog inputs, standard version 

Barrier 

D20AZ 

32 analog inputs, high-voltage version 

Compression 

D20S 

64 digital inputs, standard version 

Compression 

D20SD 

64 digital inputs, standard version 

DB25 

D20SX 

64 digital inputs, standard version 

Disconnect 

D20SB 

64 digital inputs, standard version 

Barrier 

D20SZ 

64 digital inputs, high-voltage version 

Compression 

Summary of Contents for D20












































































































Reviews: