Figure 1: Wall Plate Install
Figure 2: Mounting Box Install
Figure 3: Button PE Wiring
Figure 4: Plate / Mounting Box Installed
WIRING
3
• Reinstall Button PE, Motion sensor, or Transformer if
previously removed (Figure 3).
• Position fixture in vicinity of mounting box or plate.
• Make electrical connections in accordance with the
National Electrical Code and any applicable local code
requirements.
• Connect supply leads using wire nuts and fixture wiring
with quick connects.
• Use two provided screws to install housing to box or
plate. For ADA Compliant wall plate installations, use
shorter set of screws and tighten screws until fixture is
less than 4” from the wall.
• Insert two provided plugs into housing cover screw holes.
MAINTENANCE/CLEANING
STORAGE
OCCUPANCY SENSOR (OPTIONAL)
4
5
6
• To maintain light output, occasional cleaning of the
outer lens surface may be needed.
• Use a mild, non-abrasive soap or detergent, of neutral
pH (pH 6 to 8) containing no chlorinated or aromatic
hydrocarbons.
• Wash using a soft cloth. Rinse with clean, cold water
and wipe dry.
• Packaged units should NOT be stored unprotected
outdoors in corrugated boxes (cardboard boxes).
• Store packaged units in a covered dry area not
exceeding -40°C (-40°F) to 50°C (122°F) such as a
roofed area or covered with a secured tarp to keep
water off the corrugated (cardboard) packaging.
• The occupancy sensor ships with a default program.
Remote Programmer part number: (Sold Separately
as 197634).
• Photoelectric control is integrated through the motion
sensor, and is offered as standard.
7.366
4.800
1.000
1.020
6.320
8.266
4.300
3.853
Gasket
Gasket
1/2 “ Conduit
Knock Out
3 Places
Button PE
Option
1.375
1.750
Gasket
Motion Sensor
Option
Button PE
Option
4.300
4.800
1.750
1.690
0.970
45°
1.750 1.372
8.267
1.750
0.190
0.970 1.688
45°
0.190 TYP
Wall Plate
Housing
Housing
Wall
Gasket
Wall Gasket
Housing
Gasket
Housing Gasket
Mounting Box
Knockout
Plug
7.366
4.800
1.000
1.020
6.320
8.266
4.300
3.853
Gasket
Gasket
1/2 “ Conduit
Knock Out
3 Places
Button PE
Option
1.375
1.750
Gasket
Motion Sensor
Option
Button PE
Option
4.300
4.800
1.750
1.690
0.970
45°
1.750 1.372
8.267
1.750
0.190
0.970 1.688
45°
0.190 TYP
Wall Plate
Housing
Housing
Wall
Gasket
Wall Gasket
Housing
Gasket
Housing Gasket
Mounting Box
Knockout
Plug
Incoming
Supply
White
White
Black
Black
LED
Driver
PE
RED
7.366
4.800
1.000
1.020
6.320
8.266
4.300
3.853
Gasket
Gasket
1/2 “ Conduit
Knock Out
3 Places
Button PE
Option
1.375
1.750
Gasket
Motion Sensor
Option
Button PE
Option
4.300
4.800
1.750
1.690
0.970
45°
1.750 1.372
8.267
1.750
0.190
0.970 1.688
45°
0.190 TYP
Wall Plate
Housing
Housing
Wall
Gasket
Wall Gasket
Housing
Gasket
Housing Gasket
Mounting Box
Knockout
Plug
All trademarks are the property of their respective owners. Information provided is subject to
change without notice. All values are design or typical values when measured under laboratory
conditions. Current, powered by GE is a business of the General Electric Company.
© 2017 GE.
www.currentbyge.com
GEH6060 (Rev 0
/
/1
) English
• Water tight conduit connections are required when
using knock-outs on mounting box.
• For irregular surfaces (block, brick, etc), caulk the wall
plate or mounting box to surface interface with
generic non-hardening sealant (not provided) across
the top, and both sides (Figure 4)
These instructions do not purport to cover all details or variations in equipment nor to provide for every possible contingency to be met in connection with installation,
operation or maintenance. Should further information be desired or should particular problems arise which are not covered sufficiently for the purchaser’s purposes, the
matter should be referred to GE.
