GE CARESCAPE Monitor B850 Service Manual Download Page 70

Page: 70 / 192

CARESCAPE Monitor B850

2106778-001

With the module properly oriented, align the module insertion guide slot with the insertion
guide.

Push the module into the frame until it clicks.

To remove a parameter module, grasp it firmly, press the release lever on bottom of
module, and pull out of the guides.

6.4.5 Connecting a PDM module to an F5 Frame

NOTE: When the PDM is used without a battery, it is necessary to allow additional time to power
up. Do not interrupt the startup sequence by unplugging the PDM.
1.

Align the PDM with the insertion guides on the outside of the frame. Push the module into
the frame until it stops.

6.4.6 Installing a PDM module to a mounting solution

WARNING

PHYSICAL INJURY- Take care when mounting devices to an IV pole. If a

device is mounted too high the IV pole may become unbalanced and tip
over.

Summary of Contents for CARESCAPE Monitor B850

































































































































































































Search results

Summary of Contents for CARESCAPE Monitor B850

Reviews:

Related manuals for CARESCAPE Monitor B850

Brands by name

Popular brands

GE CARESCAPE Monitor B850, Service Manual

Search results

Summary of Contents for CARESCAPE Monitor B850

Reviews:

Related manuals for CARESCAPE Monitor B850

Brands by name

Popular brands