manualshive.com logo in svg

GE auisys cs2, User'S Reference Manual

The GE Auisys CS2 User's Reference Manual is a comprehensive guide packed with all the necessary information to effortlessly operate your device. This well-structured manual can be downloaded for free from our website, allowing you to access it anytime, anywhere. Enhance your user experience with our downloadable manual at manualshive.com.

Share
Download
background image

Integral system components

This anesthesia system contains the following integral components,
monitoring devices, alarm systems, and protection devices that
comply with European, international, and national standards:

•

Breathing system pressure-measuring device.

•

Airway pressure-limitation device.

•

Exhaled-volume monitor.

•

Breathing system integrity alarm.

•

Breathing system continuing-pressure alarm.

•

O2 monitor (optional O2 cell).

•

Anesthesia ventilator.

•

Breathing system.

•

Anesthetic vapor delivery device.

Not integral system components

These devices are not integral to this anesthesia system:

•

CO2 monitor.

•

Anesthetic agent monitor.

•

O2 monitor (when O2 cell is not installed).

•

Suction regulator.

•

EZchange canister system.

•

Condenser.

When adding devices to the anesthesia system, follow the
installation instructions provided by the device manufacturer.
Whoever adds individual devices to the anesthesia system shall
provide instructions on how to enable the individual devices. For
example, a preoperative checklist.

System accessories

These devices can be used as accessories on this anesthesia
system:

•

Suction regulator.

•

EZchange canister system.

•

Condenser.

•

Aladin and Aladin2 vaporizer cassettes.

1 Introduction

2067226-001

1-15

Summary of Contents for auisys cs2













































































































































































































































































Reviews:

No comments

Related manuals for auisys cs2

DARKSTAR TECHNOLOGIES D340 Manual To Operation preview
D340
Brand: DARKSTAR TECHNOLOGIES Pages: 4
TDW D2000 Maintenance Manuallines preview
D2000
Brand: TDW Pages: 2
Taurus 1170 Assembly And Operating Instructions Manual preview
1170
Brand: Taurus Pages: 25
Vancare G Series Quick Reference Manual preview
G Series
Brand: Vancare Pages: 3
Paitec ES-2000 User Manual preview
ES-2000
Brand: Paitec Pages: 14
NCR 7709 Kit Instructions preview
7709
Brand: NCR Pages: 20
DARAY X740 Operating & Installation Manual preview
X740
Brand: DARAY Pages: 32
Darco Body Armor Night Splint Manual preview
Body Armor Night Splint
Brand: Darco Pages: 2
MacDon D65 Installation Instructions Manual preview
D65
Brand: MacDon Pages: 74
Yamaha QX1 Owner'S Manual preview
QX1
Brand: Yamaha Pages: 46
Rapala VORTEX Operator'S Manual preview
VORTEX
Brand: Rapala Pages: 14
S.R.Smith VORTEX Assembly And Installation Instructions Manual preview
VORTEX
Brand: S.R.Smith Pages: 43
M-Audio X-Session Pro User Manual preview
X-Session Pro
Brand: M-Audio Pages: 12
M-Audio USB OMNISTUDIO Manual Del Usuario preview
USB OMNISTUDIO
Brand: M-Audio Pages: 64
M-Audio Pro Tools User Manual preview
Pro Tools
Brand: M-Audio Pages: 16
M-Audio ProjectMix I/O Quick Start Manual preview
ProjectMix I/O
Brand: M-Audio Pages: 4
M-Audio Delta 1010 Manual preview
Delta 1010
Brand: M-Audio Pages: 52
MagCore Plus II Troubleshooting Manual preview
Plus II
Brand: MagCore Pages: 80

Brands by name

Popular brands

Load more brands