manualshive.com logo in svg

GE auisys cs2, User'S Reference Manual

The GE Auisys CS2 User's Reference Manual is a comprehensive guide packed with all the necessary information to effortlessly operate your device. This well-structured manual can be downloaded for free from our website, allowing you to access it anytime, anywhere. Enhance your user experience with our downloadable manual at manualshive.com.

Share
Download
background image

6.

PEEP

7.

Flow waveform

8.

TV

Figure 11-8 • SIMV PCV-VG waveforms

PSVPro mode

PSVPro is pressure supported ventilation with apnea backup.
PSVPro is a spontaneous mode of ventilation that provides a
constant support pressure once the ventilator senses that the patient
has made an inspiratory effort. In this mode, the clinician sets the
Pressure Support (Psupport) and PEEP levels. The patient
establishes the rate, inspiratory flow, and inspiratory time. The tidal
volume is determined by the pressure, lung characteristics, and
patient effort.
PSVPro uses an inspiration termination level that establishes when
the ventilator will stop the pressure-supported breath and cycle to the
expiratory phase. The inspiration termination level is user adjustable
from 5 to 75%. This parameter sets the percent of peak inspiratory
flow that the ventilator uses to end the inspiratory phase of the
breath and to cycle into the expiratory phase. If the inspiration
termination is set to 30% then the ventilator will stop inspiration when
the flow decelerates to a level equal to 30% of the measured peak
inspiratory flow. The lower the setting, the shorter the inspiratory
phase.
An apnea backup mode is provided if the patient stops breathing.
When setting this mode the clinician adjusts the inspiratory pressure
(Pinsp), respiratory rate (RR), and the inspiratory time (Tinsp). As
long as the patient is triggering the ventilator and the apnea alarm
does not activate, the patient will get pressure-supported breaths
and the ventilator will not deliver machine breaths.
If the patient stops triggering the ventilator for the set apnea delay
time, the apnea alarm will activate and the ventilator will
automatically switch to the backup mode that is SIMV PCV. Once in
this mode the ventilator will begin delivering machine pressure
controlled breaths at the inspiratory pressure level, inspiratory time,
and rate that the user has set. If, during this time, the patient takes
spontaneous breaths in between the machine breaths, the patient
will receive pressure supported breaths.
PSVPro mode settings:

•

Psupport

•

PEEP

•

Trig Window

•

Flow Trigger

•

End of Breath

•

Pmax

•

Backup Time

Aisys CS²

11-32

2067226-001

Summary of Contents for auisys cs2













































































































































































































































































Reviews:

No comments

Related manuals for auisys cs2

p-light Maxi Installation And Instructions For Use preview
Maxi
Brand: p-light Pages: 28
Eagle Eye SG-1000 User Manual preview
SG-1000
Brand: Eagle Eye Pages: 21
Labomed Magna User Manual preview
Magna
Brand: Labomed Pages: 67
h/p/cosmos 190/65 3p Original Instruction preview
190/65 3p
Brand: h/p/cosmos Pages: 81
Raymarine H6 System Installation Manual preview
H6
Brand: Raymarine Pages: 124
Raymarine H6 Owner'S Manual preview
H6
Brand: Raymarine Pages: 192
Keller HPX Operating Instructions Manual preview
HPX
Brand: Keller Pages: 12
MacDon D50 Installation Manual preview
D50
Brand: MacDon Pages: 49
MacDon D50 Unloading And Assembly Instructions preview
D50
Brand: MacDon Pages: 49
MacDon D50 Quick Start Manual preview
D50
Brand: MacDon Pages: 4
M-Audio FireWire 1814 Quick Start Manual preview
FireWire 1814
Brand: M-Audio Pages: 3
Parker HTG Series Service Procedure preview
HTG Series
Brand: Parker Pages: 64
Parker F11 series Service Spare Parts List preview
F11 series
Brand: Parker Pages: 40
Parker Matrx Digital MDM Cabinet Mount Installation Instructions preview
Matrx Digital MDM
Brand: Parker Pages: 20
MadLab Bleep-o-tron Quick Start Manual preview
Bleep-o-tron
Brand: MadLab Pages: 7
Harken Ti-Lite Carbo AirBlock 351 Instructions preview
Ti-Lite Carbo AirBlock 351
Brand: Harken Pages: 2
Thoratec CentriMag RVAS Instructions For Use Manual preview
CentriMag RVAS
Brand: Thoratec Pages: 8
Vectra Fitness on-line 1250 Owner'S Manual preview
on-line 1250
Brand: Vectra Fitness Pages: 18

Brands by name

Popular brands

Load more brands