background image

Consumer Support

Troubleshooting T

ips

Operating Instructions

Safety Instructions

Installation Instructions

13

Install the Case in the Window

Cut the window sash seal to the window width

and stick the adhesive side to the bottom of 

the sash.

Thread two type C bolts into the support

brackets.
Slide the case into the window and lower the

window behind the top mounting rail.
Position the brackets on the case bottom so

they will be near the outermost point on the

window sill. Attach the support brackets to 

each side of the case bottom using 4 type A

screws on each side. The case should be 

slightly tilted to the outside. Use a level; 

about a 1/2 bubble will be the correct case 

slant to the outside.

Locate the 3 screw holes along the bottom front

edge of the case. Center the case, side to side, 

in the window and mount it to the window sill

using 3 type B screws.

Extend the left and right accordion panels to

the vertical window sashes and attach with 4

type B screws. 

D

C

B

A

6

Window sash seal

Type B 
screws

Type B 
screws

Top mounting rail

Type B screws

Install the Security Bracket and the Foam Top Window Gasket

Attach the security bracket with a type B screw.

Cut the foam top window gasket to the 

window width.
Stuff the foam between the glass and the

window to prevent air and insects from getting

into the room.

C

B

A

7

Type C bolts

Type A screws

Summary of Contents for ASD06*





















Reviews: