background image

Care and Cleating

USER MAINTENANCE
INSTRUCTIONS

Turn 

 conditioner off 

remove plug from wall outlet
before cleaning.

Grille & Cabinet

Wipe front grille with   

 cloth

lightly dampened with mild 

 detergent. Wash

cabinet with mild soap or detergent

 lukewarm water.

Outdoor Coil

This 

 

 the outdoor side

 the unit 

 be checked

periodically and cleaned if
clogged with dirt or soot from
the atmosphere.   extremely
soiled, it may need to be steam
cleaned,   service available
through your GE service outlet,

Front Grille

Remove the front 

   the

window sill prevents removal 
the air filter or if you need to read
the model and serial numbers.

To remove the grille:

Step 1: Remove and save the screw
that 

 the grille to the chassis.

Step 2: Press inward on the lower
right side of the cabinet until the
tab is clear 

 the slot and allow the

grille to come toward you slightly.

Step 3: Repeat this process 

 the

lower left side.

 

 pull 

 

 

 

 

 than 3 

 

 

 the 

 2 

 

 

 

Step 4: Grasp the grille’s lower
right and left corner and carefully
lift straight upward to disengage the
2 top tabs from their slots in the

cabinet front edge.

CABINET

 

To attach the grille:

The grille is attached on the front

 the cabinet by four tabs and a

screw.

Step 1: Lower the 2 top tabs of the

 into the 

 in the cabinet

top.

Step 2: Carefully push the sides of
the grille over the cabinet sides
until the side tabs lock into the
slots.

 

 strike 

 hit the

 

 

   

 

 will

Step 3: Replace the screw that
holds the 

 to the chassis.

Air Filter

The air 

 behind the inlet grille

should be washed   least every 

days or as often as it needs cleaning.

To remove the filter, 

 the tab

on the filter and pull downward. 
the window sill blocks access to the
air 

 you must first remove the

front grille.

Vacuum the 

 on the dusty side

to remove light dust. Wash the
filter, cleaner side up, under 
flowing water to wash out

accumulated dust 

 lint. If the

filter is very dirty, use a mild
household detergent in the wash
water. Let the 

 dry thoroughly

before replacing it.

When replacing the filter, be sure
the word FRONT is facing you as
you slide the filter back into place.

6

Summary of Contents for AME06

















Reviews: