50
Advent Commercial Fire System
Remote Downloader Programming
Note
Downloader programming must occur on-site when pro-
gramming an Advent Commercial Fire panel. Please see
the Advent Downloader
User’s Guide
for more informa-
tion.
Although most information can be programmed at the panel,
some optional information must be programmed remotely from
Advent Downloader. Use the information you recorded in
Appendix A to inform the downloading operator of the pro-
gramming requirements for this system.
Advent Downloader Programming
Note
The
Enable Remote Access setting (17086)
must be set to
“on” in order for remote downloader programming to be
enabled. This setting defaults to “on”.
To initiate an upload/download session from the
panel:
1.
Contact your download station and ask the operator to
prepare for an upload/download session.
2.
Make sure the panel is connected to a phone line and
that premises telephones are on hook (hung up).
3.
Enter panel programming and verify/enter the follow-
ing downloader settings:
17107 Dealer Access Code—Must match (in Advent
Downloader
and
at the panel) or be left at default.
17108 Downloader Access Code—Must match (in
Advent Downloader
and
at the panel) or be left at
default.
17109 Downloader Account Number—Must match
(in Advent Downloader
and
at the panel) or be left at
default.
yy001 (23001 or 24001) Phone Number Enable—
Must be “on” for panel to call the downloader.
yy002 (23002 or 24002) Phone Number—At least one
downloader phone number must be programmed.
(Programming the phone number automatically
enables it.)
4.
Enter
0
+
2
+
install code (0123)
.
5.
For an upload enter
1
, a download press
2
, and a gen-
eral upload/download press
3
. The session will start
and the system will return to the previous arming level.
Note
The panel software versions (in Advent Downloader
and
at
the panel) must match.
If the panel displays
DOWNLOAD FAILURE
contact the
downloader station to verify the downloader phone num-
ber and settings.
Installing Line Carrier Devices
This section describes how to install X10 Lamp, Appliance,
and Universal Module line carrier (wireless) line carrier
devices.
Note
The operation of X10 modules is for supplementary pur-
poses only.
Programming the Panel House Code
Please see item numbers xx022 and xx023 (page 21) for
information on setting house codes.
Installing X10 Modules
When installing X10 modules:
Use only incandescent lamps with lamp modules.
Do not plug X10 modules into outlets controlled by a
switch.
Do not use extension cords to connect several lamps or
appliances to one module.
&$87,21
Use X10
Lamp
Modules to control light fixtures – do not
use X10
Appliance
or
Universal
Modules. Appliance and
Universal Modules are not controlled during an alarm.
To install X10 modules:
1.
Plug the lamp or appliance cord into the bottom of the
module.
2.
Plug the module into a lower AC outlet.
3.
Refer to Table B.5 on page 97 for the house code you
programmed into the panel, and then find the letter that
corresponds to that house code. Each letter setting rep-
resents one panel house code. For example, house code
1 corresponds with “A” on the X10 module house dial.
Print History Buffer
50016
(Default = n/a) Prints events based on a time range.
To Print History Buffer:
1.
Enter
50016
. The display shows
ENTER HISTORY
START
.
2.
Enter the desired start date in mm/dd/yy format. For
example, if you wanted to print events starting on
September 1, 1999 you would enter 090199. The display
shows
ENTER HISTORY STOP.
3.
Enter the desired stop date in mm/dd/yy format. Events
occurring within that time frame will print.
Delete Primary SnapCard
Delete Secondary SnapCard
Primary: 50014, Secondary: 50015
(Default = n/a) This setting enables you to delete a SnapCard
when it is being replaced with a different type of SnapCard. All
inputs/outputs for the new card must be programmed.
Note
If you are replacing the SnapCard with the same type of
SnapCard you don’t have to perform this procedure and
can keep the current input/output settings.
To Delete SnapCard Information:
1.
Enter the installer code.
2.
Enter the desired item number. The panel displays
SNAP-
CARD DELETED
.
Summary of Contents for Advent
Page 56: ...54 Advent Commercial Fire System ...
Page 88: ...86 Advent Commercial Fire System ...
Page 110: ...108 Advent Commercial Fire System ...
