Use the scroll bar to see all of the options on the screen:
Event History.
Touch the related Show button to view system
events.
Panel Status.
Touch the related Hear button to listen to the
status of your security system. If you have a Simon XT v1.4,
touch the Clear button to clear status.
Chime.
Touch the On or Off button to toggle the touch screen
chime feature on or off. This feature will enable this touch
screen to speak or beep when a door opens. The security panel
chime must be enabled. Refer to the security panel
documentation for information on this feature.
Lights.
If you have a Simon XT v1.4, touch Control to access the
light screen. From the Light screen, you can select all
programmed lights on, or all programmed lights off or
individually select whether your lights are on or off. (Light status
is not indicated on this screen). If you have a Simon XT v1.3,
touch the On or Off button to control lights within your system.
Door Locks
. If you have a Simon XT v1.4, touch Control to
access the Door Lock screen. From the Door Lock screen, you
can lock or unlock all programmed doors. You can also select
individual programmed doors. The button will flash until
confirmation is received from the door lock that the command
was successful.
Note:
Action does not guarantee a door is locked and
closed.
Voice Volume.
Touch the arrow buttons to adjust this touch
screen’s speech volume level (the siren sounds are not
controlled by this setting).
Beep Volume
. Touch the arrow buttons to adjust this touch
screen’s beep volume level (the siren sounds are not controlled
by this setting).
Brightness.
Touch the arrow buttons to adjust the brightness
level of this touch screen’s screen.
Default screen.
Use this feature to set this touch screen’s
screen saver mode. Select “Blank” to have the screen and LED
go dark after a period of inactivity. Otherwise, the default will be
the Home screen and the screen will always be lit. If AC power is
lost, the screen will go blank after 2 minutes of inactivity to
maximize battery life.
Note:
The touch screen will automatically blank at 2:00 am
daily for 60 minutes.
RF Test.
For installer use only.
Calibration.
Normally you will not need to calibrate the touch
screen, but if the touch screen buttons do not respond correctly,
touch the Show button to access the Calibration screen. To
calibrate the touch screen, touch the + icons in the corners on
the Calibration screen using a soft, fine point.
If you cannot access the calibration using the above procedure,
use the following steps:
1. Press and hold the Reset button (Figure 1).
2. Press and hold anywhere on the screen.
3. While you are pressing the screen, release the Reset
button.
4. Follow the calibration prompts.
Help.
Touch the Help button to access the Help menu. The Help
menu will display a list of various help topic buttons. Touch the
buttons for information on the given topic.
Code Required Access.
Touch the On or Off buttons to toggle
this feature. When turned on, it will require a user access code
to be entered for most touch screen functions. With code
required access, not all icons will be displayed.
Clear and Enroll.
Do not touch this button; it is used by the
installer for installation only.
Battery replacement
When the touch screen batteries are low, the touch screen will
display the red battery icon on the Home and Settings screens.
Note:
We recommend that you replace the batteries once a year
and after any significant power outage.
1. Remove the touch screen from the mounting plate by
inserting a small screwdriver into the slot on the bottom of
the touch screen.
2. Replace all batteries being sure to follow the polarity
instructions (replace with four 1.5 V, Alkaline AAA batteries).
Avoid touching the touch screen face while you are replacing
the batteries.
3. Briefly disconnect the AC power (this will clear the battery
fault).
4. Reconnect AC power.
Note:
If AC power is lost and batteries are not present or are
depleted, the touch screen will not power up until AC power is
restored (even if new batteries are installed).
Cleaning the touch screen
If necessary, use a soft cloth to clear smudges on the screen; do
not use glass cleaner on the screen.
Reset button
The Reset button is located on the bottom left side of the touch
screen mounting plate. To power cycle the touch screen, use a
toothpick to depress the recessed Reset button.
Figure 1: Reset button
Opening slot
Reset button
P/N 466-2401 • REV A • ISS 17JAN11
3 / 4
