GE 6'' QuickPanel View Hardware User'S Manual Download Page 63

Page: 63 / 76

GFK-2327B

Chapter 3 Detailed Operation

3-35

To remove the internal battery

1. Disconnect AC power from the DC supply.

2. Open the rear access panel.

3. Release the battery by

gently

lifting it from the completely exposed side,

past the small protrusions. To avoid breaking the battery retainer clips,
do not apply excessive upward pressure.

4. Slide the battery out of its carrier, noting the arrow on the carrier

indicating the direction of removal.

To install a new battery

1. Disconnect AC power from the DC supply.

2. Open the rear access panel.

Note:

Battery must be installed with positive (

) side up.

3. To install the battery, insert one side of the battery into the upper side of

the battery clip, then press the other side into the clip until snaps into
place.

Warning

Replace battery with Panasonic BR2032 only. Use of another
battery may present a risk of fire or explosion.

Warning

Battery may explode if mistreated. Do not recharge,
disassemble or dispose of in fire.

Summary of Contents for 6'' QuickPanel View













































































Search results

Summary of Contents for 6'' QuickPanel View

Reviews:

Related manuals for 6'' QuickPanel View

Brands by name

Popular brands

GE 6'' QuickPanel View, Hardware User'S Manual

Search results

Summary of Contents for 6'' QuickPanel View

Reviews:

Related manuals for 6'' QuickPanel View

Brands by name

Popular brands