Specifications and Ordering Information
Part Number 141500-01
Rev. J (06/07)
Page 4 of 6
Ordering Information
For spares, order the complete catalog number as
described below. This includes a front panel
assembly, monitor PWAs with sheet metal, and
appropriate relay module. This unit is optioned,
tested and ready to install in your system. Spare
relay modules can be ordered separately.
Dual Thrust Position Monitor
3300/20-AXX-BXX-CXX-DXX-EXX
Option Descriptions
A:
Full-scale Range Option
0 1
25-0-25 mils
0 2
30-0-30 mils
0 3
40-0-40 mils
0 5
50-0-50 mils
0 6
75-0-75 mils
1 1
0.5-0-0.5 mm
1 2
1.0-0-1.0 mm
1 3
2.0-0-2.0 mm
B:
Transducer Input Option
0 1
3300 or 7200 Proximitor®
systems, 200 mV/mil (Ranges
01, 02, 03, 11, and 12 only.)
0 2
7200 11 mm (not 3300XL)
Proximitor system, 100 mV/mil
0 3
7200 14 mm or 3300 HTPS
Proximitor systems, 100
mV/mil
0 4
3000 Proximitor® 200 mV/mil
(Transducer Output Voltage in
power supply must be set for –
18 Vdc or use power conver-
ter. Ranges 01 and 11 only.)
0 5
3300XL NSv and 3300 RAM
Proximitor Sensor, 200 mV/mil
(Ranges 01 and 11 only).
Note:
1.
For 3300 XL 11mm transducers, use mod 146300-01.
2.
Contact your nearest sales professional if 3000 series
transducers are to be used in a monitoring system
which also uses 3300 and/or 7200 Series transducers.
C:
Alarm Relay Option
0 0
No Relays
0 1
Epoxy-sealed
0 2
Hermetically-sealed
0 3
Quad Relay (Epoxy-sealed
only)
0 4
Spare Monitor-No SIM/SIRM
Notes:
1.
AND voting logic is not available with Quad Relays.
2.
At least one relay module must be ordered with each
3300 System. If one common relay module per system
has been ordered, all monitors of this type must be
jumper programmed at the factory to activate a relay
bus. Order SCK (Special Configuration Kit) 157520-119
& -120 for bus one or 157520-121 & -122 for bus two.
3.
Agency approval places limitations on the relay
module. Refer to the Relay Module data sheet for
information.
4.
Quad Relays are not available with the Internal Safety
Barriers option.
D:
Agency Approval Option
0 0
Not required
0 1
CSA/NRTL/C
0 2
ATEX self certification
Note:
ATEX approval requires the monitor rack be installed in a
weatherproof housing.
E:
Safety Barrier Option
0 0
None
0 1
External
0 2
Internal
Spare Relay Module Assemblies
(Order the option in parenthesis for ATEX approved
spares)
81544-01(02)
No Relays
81545-01(02)
Dual Epoxy Relays
81546-01(02)
Dual Hermetic Relays
84152-01(02)
Quad Relays
88984-01(04)
Dual Hermetic, Internal Barriers
88984-02(05)
Dual Epoxy, Internal Barriers
88984-03(06)
No Relay, Internal Barriers
Notes:
1.
External Safety Barriers must be ordered separately.
