background image

16

C

AUSES

 

OF

 P

OOR

 R

ECEPTION

• Aluminum siding.

• Foil backing on insulation.

• Heating ducts and other metal construction can shield radio signals.

• You’re too close to appliances such as microwaves, stoves,

computers, etc.

• Atmospheric conditions, such as strong storms.

• Base is installed in the basement or lower floor of the house.

• Base is plugged into an AC outlet with other electronic devices.

• Baby monitor is using the same frequency.

• Handset battery is low.

• You’re out of range of the base.

S

ERVICE

The FCC requires this product to be serviced only by the manufacturer or
its authorized service agents. In accordance with FCC requirements,
changes or modifications not expressly approved by Thomson Consumer
Electronics could void the user’s authority to operate this product. For
instructions on how to obtain service, refer to the warranty included in this
Guide or call Consumer Information, 1-800-448-0329.

Attach your sales receipt to the booklet for future reference or jot down the
date this product was purchased or received as a gift. This information will
be valuable if service should be required during the warranty period.

Purchase date _____________

Name of store ________________

Summary of Contents for 2-9750





















Reviews: