background image

Problem

Possible Causes

What To Do

Clock does not work

Plug on range is not completely 

Make sure electrical plug is plugged into a live,  

inserted in the electrical outlet.

properly grounded outlet.

A fuse in your home may be 

Replace the fuse or reset the circuit breaker.

blown or the circuit breaker
tripped.

Oven controls improperly set.

See the 

Using the clock and timer

section.

Food does not bake

Oven controls improperly set.

See the 

Using the oven

section.

or roast properly

Rack position is incorrect.

See the 

Using the oven

section.

Incorrect cookware or cookware  

See the 

Using the oven

section.

of improper size being used.

Oven thermostat needs 

See the 

Adjust the oven thermostat—Do it yourself! 

section.

adjustment.

Clock not set correctly.

See the 

Using the clock and timer

section.

Aluminum foil used improperly

See the 

Care and cleaning of the range

section.

in the oven.

Oven bottom not securely

See the 

Installation of the range

section.

seated in position.

Food does not

Oven controls improperly set.

See the 

Using the oven

section.

broil properly

Oven door and/or broiler drawer 

See the 

Broiling

section.

not closed.

Improper rack position

See the 

Broiling guide.

being used.

Food being cooked in a hot pan.

Use the broiling pan and grid that came with your 
range. Make sure it is cool.

Cookware not suited for broiling.

Use the broiling pan and grid that came with your range.

Aluminum foil used on the 

See the 

Using the oven

section.

the broiling pan and grid has 
not been fitted properly and 
slit as recommended.

Oven bottom not securely

See the 

Installation of the range

section.

seated in position.

Oven temperature 

Oven thermostat 

See the 

Adjust the oven thermostat—Do it yourself! 

section.

too hot or too cold

needs adjustment.

Oven light does not work

Light bulb is loose or defective.

Tighten or replace the bulb.

Plug on range is not completely 

Make sure electrical plug is plugged into a live, properly 

inserted in the electrical outlet.

grounded outlet.

Oven not heating up

Pilot is not lit (on standing

See the 

Light the Oven Pilot 

section in the 

Installation

pilot models).

Instructions.

GEAppliances.com

41

Consumer Support

Operating Instructions

Safety Instructions

Installation Instructions

Tr

oubleshooting T

ips

Summary of Contents for 183D5580P236

















































Reviews: