GE Multilin 469 Instruction Manual Download | Manualshive

Page: 217 / 338

background image

CHAPTER 5: SETTINGS

469 MOTOR MANAGEMENT RELAY – INSTRUCTION MANUAL

5–75

5.9.6

Open RTD Sensor

PATH: SETTINGS

ZV

S8 RTD TEMPERATURE

ZV

OPEN RTD SENSOR

The 469 has an Open RTD Sensor alarm. This alarm will look at all RTDs that have either an
alarm or trip programmed and determine if an RTD connection has been broken. Any RTDs
that do not have a trip or alarm associated with them will be ignored for this feature. When
a broken sensor is detected, the assigned output relay will operate and a message will
appear on the display identifying the RTD that is broken. It is recommended that if this
feature is used, the alarm be programmed as latched so that intermittent RTDs are
detected and corrective action may be taken.

5.9.7

RTD Short/Low Temp

PATH: SETTINGS

ZV

S8 RTD TEMPERATURE

ZV

RTD SHORT/LOW TEMP

The 469 has an RTD Short/Low Temperature alarm. This alarm will look at all RTDs that
have either an alarm or trip programmed and determine if an RTD has either a short or a
very low temperature (less than –50°C). Any RTDs that do not have a trip or alarm
associated with them will be ignored for this feature. When a short/low temperature is
detected, the assigned output relay will operate and a message will appear on the display
identifying the RTD that caused the alarm. It is recommended that if this feature is used,
the alarm be programmed as latched so that intermittent RTDs are detected and
corrective action may be taken.

OPEN

[

OPEN RTD SENSOR:

Off

Range: Off, Latched, Unlatched

MESSAGE

ASSIGN ALARM

RELAYS:

Range: Alarm, Alarm & Auxiliary2,

Alarm & Aux2 & Aux3, Alarm &
Auxiliary3, Auxiliary2, Aux2 &
Aux3, Auxiliary3

MESSAGE

OPEN RTD SENSOR

ALARM EVENTS: Off

Range: On, Off

RTD

[

RTD SHORT/LOW

TEMP

Range: Off, Latched, Unlatched

MESSAGE

ASSIGN ALARM

RELAYS:

Range: Alarm, Alarm & Auxiliary2,

Alarm & Aux2 & Aux3, Alarm &
Auxiliary3, Auxiliary2, Aux2 &
Aux3, Auxiliary3

MESSAGE

RTD SHORT/LOW

TEMP

Range: On, Off

«
...
215
216
217
218
219
...
»

Summary of Contents for 469



















































































































































































































































































































































Reviews:

No comments

Related manuals for 469

Brand: CAMDEN Pages: 26

Brand: IFM Electronic Pages: 64

Brand: National Instruments Pages: 65

Brand: TE Connectivity Pages: 4

Brand: ABB Pages: 21

Brand: Moeller Pages: 2

MINIA MMR-HL-001-A230

Brand: OEZ Pages: 8

Brand: ELMON Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands