background image

8 - TIMES LEARNING

PRELIMINARY WARNINGS:

Values loaded by default:

   - Working time:  60 s;

     - Pause time : 30 s;

Be sure that the shutter is completely closed before making the learning procedure.

• Check the correct position of the limit switch.

Ÿ

Ÿ

automatic closing require 2 different procedures. 

Ÿ

 

The learning of working time and 

PROGRAMMING OF THE AUTOMATIC RECLOSING TIME:

•  When the shutter is closed, put DIP2 in ON, then DIP3 in ON 

Ÿ

LED DL9 will turn on  fixed.

• Give any command  (OPEN / CLOSE/ START)

Ÿ

An acoustic signal will show the beginning of pause time counting, LED DL9 will start blinking every second

• After the required time (MAX. 180 s), give any command (OPEN / CLOSE/ START);

Ÿ

A double acoustic signal and LED DL9 turning off will show that the operation has been successful;

Ÿ

Put DIP 3 in OFF 

PROGRAMMING OF THE WORKING TIME:

•  When the shutter is closed,  put DIP2 in OFF, then  DIP3 in ON

Ÿ

LED DL9 will turn on  fixed.

• Give any command ( OPEN / CLOSE/ START);

Ÿ

The shutter will start the opening phase, LED DL9 will turn off and an acoustic signal will show the beginning of     

    the opening time counting.

Ÿ

The intervention of a photocell / edge will be irrelevant; 

• On  reaching  the  opening  limit  switch  or  after  any  command  (OPEN  /  CLOSE/  START),  the  motion
   will block;

Ÿ

LED DL9 will turn on fixed.

• Give any command ( OPEN / CLOSE/ START)

Ÿ

The shutter will start the closing phase and LED DL9 will turn off .

Ÿ

The intervention of a photocell / edge will temporarly block the counting and the closing manoeuvre of the 

shutter, it is necessary to start again from the previous point. 

• On reaching the closing limit switch or after any command ( OPEN / CLOSE/ START), the closing  motion will  

 block;

Ÿ

LED  Dl9  will  turn  on  fixed  and  the  control  unit  will  emit  a  double  acoustic  signal,  showing  that  the             

  operation has been successful.

Ÿ

Put DIP 3 in OFF.

Ÿ

Put DIP 2 to the original state. 

IT

IT

UK

SR302

17

UK

SR302

16

9 - TRANSMITTERS PROGRAMMING

 

Operation with ONE BUTTON

!

Push the SW2 button for one second, after  releasing it the control unit will emit an acoustic signal and LED    
DL10 will turn on fixed;

!

  Push in 10 s the transmitter button you want to store as START command, a triple acoustic signal with 3 LED 

DL10 flashes will show the storage has occured;

!

  Push in 10 s the button of the new transmitter you want to store.

!

After the learning of last transmitter, wait for a double acoustic signal and LED DL10 off, showing the end of the 
procedure.

Operation with TWO BUTTONS:

!

Push the SW2 button for one second, after  releasing it the control unit will emit an acoustic signal and LED    
DL10 will turn on fixed.

!

  Push in 10 s the transmitter button you want to store as OPEN button, a triple acoustic signal with 3 LED DL10 

flashes will show the storage has occured.

!

Push in 10 s another button of the same transmitter to which you want to match the CLOSE function, a triple 
acoustic signal with 3 LED  DL10 flashes will show the storage has occured.

!

Repeat in 10 s the sequence of buttons pushes to store a new transmitter.

!

After the learning of last transmitter, wait for a double acoustic signal and LED DL10 off, showing the end of the 
procedure.

NOTE: It is possible to store again a transmitter to switch from 1 button operation to 2 buttons and vice-

versa.

The double buttons mode is possible only if the 2 buttons of the transmitter are stored during the
same learning cycle, one after the other.

            

COMPLETE CANCELLATION OF THE MEMORY

Push Sw2 button (LED L10 is on), keep pushing it as long as LED DL10 will make 10 flashes with 10 acoustic 
signals.

THE CONTROL UNIT IS COMPATIBLE ONLY WITH THE TRANSMITTERS OF MAKO 

868MHz SERIES.

DIP 7

ON

OFF

UNUSED

Unused

OFF

TERMINALS

13-14 

MANAGEMENT

DIP 8

START command is associated with terminal 14, as terminal 13 is disabled.

OPEN command is associated with terminal 14 (the control unit will open but 
won’t automatically close,even if the automatic closing is enabled), 
as CLOSE command is associated with terminal 13.

ON

The transmitters buttons already stored can be over-written at any time. 
It is possible to store 31 buttons or transmitters max.

Summary of Contents for SR302





































Reviews: