64
TROUBLESHOOTING GUIDE
SYMPTOM
POSSIBLE CAUSE
CORRECTIVE ACTION
•
The control panel display does not
Laminator not connected to
Insert attachment plug into receptacle.
illuminate when POWER ON/OFF is
electrical supply.
in the ON, marked “I”, position.
•
Heat rollers do not turn when I
Safety shield is not properly
Remove safety shield and properly replace it.
press the RUN (
) button.
installed.
Feed table not properly installed.
Tilt feed table and properly replace it.
E-STOP is engaged
Pull out on the E-STOP push button.
•
Heat rollers only turn if I use
Laminator is in Footswitch mode.
disengage the footswitch mode.
the footswitch.
•
Rear controls do not operate.
Rear controls are not enabled.
Enable rear controls.
Safety shield is not installed in
Remove the rear slitter and install the safety shield.
the rear position.
•
Laminated items exhibit curling.
Tension between the top and bottom
Adjust tension per section
FILM TENSION.
film roll is unequal.
Tension on top or bottom roll of
Adjust tension per section
FILM TENSION.
film is too loose.
Speed setting too slow.
Slightly speed up the laminator.
Bottom film roll may be improperly
Make sure bottom roll of film is around idler bar and the it is in the
loaded.
normal operating position.
Chill idler not used.
Move the chill idler to the web position.
•
Adhesive deposited on heat rollers.
Top and bottom film webs not
Release heat and pull roller pressure, align the rolls of film.
aligned.
Laminate improperly loaded.
Adhesive (matte) side of laminate film may be against the heat
rollers. Unweb and reload the film properly.
•
Unsatisfactory adhesion of laminate.
Speed setting too fast for type of
Lower speed setting by pressing SLOW button to slower speed
material being laminated.
Insufficient heat.
Wait for “READY” indicator to appear in the control panel display.
Laminate improperly loaded.
Adhesive side of film must be facing away from the heat rollers.
Bottom roll of film not threaded behind the idle bar.
Heat rollers require cleaning.
Clean heat rollers per procedure in section
CARING FOR THE GBC TALON 44/64 LAMINATOR.
Laminated item unsuitable for
Item may be dirty or may have nonporous surface that is
adhesion.
extremely difficult to laminate.
•
Waves in my output
See sub section
OUTPUT.
Under section titled
THE ART OF LAMINATION.
Nips may be out of calibration.
Place a service call for calibration check.
SERVICE AGREEMENT
GBC’s Equipment Maintenance Agreement will insure the quality performance and long life built into your laminator.
A service charge for travel time, labor and parts may be incurred for each out of warranty service call. GBC’s Equipment Maintenance Agreement
decreases these expenses and protects your valuable investment. GBC offers several types of agreements to suit your needs and budget. To
contact GBC write to:
GBC NATIONAL SERVICE
IN CANADA:
GBC NATIONAL SERVICE
ONE GBC PLAZA
49 RAILSIDE ROAD
NORTHBROOK, IL 60062 U.S.A.
DON MILLS, ONTARIO
1.847.272.3700
M3A 1B3
Part Number 930-097 Revision -
Summary of Contents for Talon 44 CE
