background image

Page 7-1

SPIRE III Series

 – Installation and Operating Instructions

c

arInG

 

For

 

tHe

 spIre s

erIes

 

l

amInator

The only maintenance required by the operator 
is to periodically clean the rollers. The following 
procedure will help keep the rollers free of dirt and 
adhesive, which has been deposited along the edge 
of the laminating film. Proper alignment of the rolls of 
film reduces the amount of adhesive on the rollers. 
Perform only the routine maintenance procedures 
referred to in these instructions. 

 

WARNINGS: 

•  Do not attempt to service or repair the laminator. 

Do not open the laminator. There are no user 
serviceable parts inside. Refer service to qualified 
service personnel.

•  Keep fingers, hands clothing, jewelry, and long 

hair away from the rollers. Clothing, jewelry and 
long hair could be caught in the rollers and pull 
you into them. 

•  Entrapment hazard. Do not operate when alone. 

More than one person is required to be in the area 
when operating the machine.

•  Do not lift, tilt, or attempt to move the laminator 

other than rolling it on its castors across flat, even 
surfaces. You can be severely injured or crushed.

Failure to observe these warnings could result in 
severe personal injury or death.

CAUTIONS:

 

•  Do not apply any cleaning fluids or solvents to the 

rollers. Some solvents and fluids could damage 
the rollers.

•  Do not allow foreign objects to fall into the working 

area of the laminator. 

Failure to observe these cautions could result 
damage to the machine.

c

leanInG

 t

He

 r

ollers

Keeping the rollers clean ensures that your finished 
items will not be damaged by dirt and adhesives. 
Clean the rollers with a clean, damp lint-free cloth. 
If there are any adhesive build ups, you may use 
isopropyl alcohol instead of water. 

•  Never clean rollers with abrasive, sharp, or 

pointed objects.

•  Do not use any other cleaning agents other 

than those listed above.

•  Accumulated adhesive deposits on the 

rollers can cause damage to the rollers. 
Rotate the rollers at the lowest speed setting 
on the control panel. Press Stop and clean 
the exposed surface of the Rollers. Repeat 
this process to clean the remaining Roller 
surfaces.

To clean the rollers and idler bar:

1.  Remove the Pressure Plate and raise the Feed 

Table. Refer to “Pressure Plate” and “Raising the 
Feed Table” s
ections. 

 WARNING: 

Raising the Feed Table exposes 

moving parts. This means you can be harmed when 
the Feed Table is raised. Make sure to lower the Feed 
Table when cleaning is completed.

2.  Remove the film from the laminator. Refer to

 the 

“Removing the Web” section.

3.  Use the dampened cloth to remove any dust, 

dirt, and other foreign materials from the rollers. 

4.  Press and release the Footswitch to rotate the 

rollers to an unclean portion. Be sure to remove 
all adhesive and dirt.

 WARNING: 

Keep fingers, hands pad, and rag 

away from the Rollers when the machine is running. 

5.  Lower the Feed Table and install the Pressure 

Plate.

7. o

perator

 m

aIntenance

Summary of Contents for Spire III 44T


















































Reviews: