P.13
主槳螺距設定
Collective Pitch Setting
Horizontal
水平
Horizontal
水平
90
o
90
o
Horizontal
水平
Horizontal
水平
①
①
11.至遙控器選單中的【伺服機微調選項的 ＂Subtrim ＂
功能】將十字盤3顆伺服機擺臂微調至垂直90度。
12.請將油門搖桿撥至中立，以螺距尺測量主旋翼的度數
是否為0度。 若不是0度，請調整①號連桿長度使2支
主旋翼均為0度。
13.調整3顆伺服機連桿長度至十字盤、相位器、日字框、
平衡翼皆水平。
14.請將油門搖桿向上撥至最高，測量主旋翼最大【正】螺距度數，應為+11至+13度。
若不是，請調整遙控器選單中【SWASH】內的【PIT】數值。
請將油門搖桿向下撥至最低，測量主旋翼最大【負】螺距度數，應為-11至-13度。
【正】【負】螺距度數需一樣若不是，請調整遙控器選單中的【伺服機大小行程量】
數值，三顆伺服機需同時增加或減少至測量結果與正螺距度數相同。
螺距量角器與平衡桿需水平
15.請將油門搖桿撥至最低點，測量主旋翼【負】螺距度數約在-2至-3度，並請進入遙控器
選單中【PITCH曲線設定】選項，至【NORM模式】中增加數值最低的數值，使主旋翼
【負】螺距度數約在-2至-3度。
【設定完的數值大約在40%至45%之間】至曲線設定中間的數值，增加數值至55至60%
◎進行第15項時請、上、下、左、右、前、後撥動搖桿，查看十字盤
行程動作是否有干涉。若有干涉請至SWASH減少AILE、ELEV數值。
螺距量角器與平衡桿需水平
螺距量角器與平衡桿需水平
11.Set the transmitter function “ Subtrim ” to adjust
the neutral position of CCPM servos, the servos
at neutral should have the servo arms at level
position, and each arm should be perpendicular
to the control linkage.
The bottom edge of the
Pitch Gauge should be
paralle to the Flybar
The bottom edge of the
Pitch Gauge should be
paralle to the Flybar
The bottom edge of the
Pitch Gauge should be
paralle to the Flybar
12.Move the throttle stick to the neutral (middle at 50%
value), use a pitch gauge to check the pitch of both
blades, adjust the linkages
①
to make sure they are
all in 0 degrees of both blades.
13.The Servo Horns / Swash
Plate / Washout Arms / Flybar Paddles and Cage
should be set to be horizontal as shown in figure.
14.Move the throttle stick to the top position, the maximum
positive pitch should be 11 to +13 degrees,
set the proper “Pitch %” in transmitter function “ Swash
Mix ”.
Move the throttle stick down to the bottom position, the
maximum negative pitch should be around -11 to -13
degrees, set the transmitter function “ Travel Volum /
End Point “ properly to make it come with recommended
negative pitch.
IMPORTANT : The increase/decrease value of the
transmitter function “ Travel Volum / End Point “ of each
CCPM servo should be the same in this step.
◎
Before starting the step 15, make sure to move the control
sticks to check the movement of the swashplate and set the
proper “AIL % and ELE %” in transmitter function “ Swash
Mix ” to make sure each mechanism is not interfered
with each other.
15.Move the throttle stick to the lowest position, set the proper “ Pitch Curve % ”
in transmitter function “ Normal Mode ” to make the negative collective pitcht
to be -2 or -3 degrees at the lowest throttle stick position( it is about 40% to
45% at the 1st pitch curve point at normal mode). The value of the middle
point of pitch curve in normal mode is about 55% to 60%.
