Gateway M460 Service Manual Download Page 32 | Manualshive

Page: 32 / 70

background image

Replacing Gateway Notebook Components

www.gateway.com

28

Replacing the keyboard

Tools you need to complete this task:

Screws removed during this task:

To replace the keyboard:

1

Complete the steps in

“Preparing the notebook” on page 5

2

Remove the keyboard cover by following the instructions in

the keyboard cover” on page 26

.

Tips & Tricks

The screw hole is marked with a K.

3

Turn the notebook over so the bottom is facing up.

4

Remove the keyboard screw.

Flat-blade driver

Scribe or non-marring tool

- OR -

Phillips #0 screwdriver

2 black (keyboard cover)

1-3 black (keyboard)

Screw

«
...
30
31
32
33
34
...
»

Summary of Contents for M460







































































Reviews:

No comments

Related manuals for M460

Toughbook CF-18BCAGCMM

Brand: Panasonic Pages: 52

Brand: Fujitsu Siemens Computers Pages: 3

Education Chromebook

Brand: rgs Pages: 12

Universal Car/Air Adapter

Brand: Kensington Pages: 7

Brand: EUROCOM Pages: 104

Brand: DIGILION Pages: 15

Joybook Lite T132

Brand: BenQ Pages: 68

Galaxy Book Pro NP935XDB-KC1UK

Brand: Samsung Pages: 105

Brand: HP Pages: 106

Brand: HP Pages: 89

2200 - Presario - 16 MB RAM

Brand: HP Pages: 182

Brand: HP Pages: 69

Brand: HP Pages: 110

Brand: HP Pages: 82

2140 - Mini-Note - Atom 1.6 GHz

Brand: HP Pages: 114

Brand: HP Pages: 91

Brand: HP Pages: 76

Brand: HP Pages: 106

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands