Gateway 930 series System Manual Download | Manualshive

Page: 122 / 160

background image

114

Troubleshooting

Hard drive problems

The system does not recognize the SCSI drive.

The system does not recognize the IDE drive.

Probable cause

Solution

The SCSI chain is not
properly terminated

Make sure the last device on the SCSI chain
is properly terminated.

The drive is configured with a
conflicting SCSI address

Change the device’s SCSI address to one that
is not currently being used by the system.

The cables are not connected
correctly

Open the system and make sure the cable
connections are correct.

Probable cause

Solution

The primary IDE device may
be configured incorrectly

Restart your server, then press

F

1

to open the

BIOS Setup utility. From the Advanced | IDE
Configuration menu, set the IDE Controller
to Both and the Primary IDE Master to Auto.

The drive may not be
configured properly

Consult the hard drive user’s guide for
instructions on how to configure the drive.
Configure the drive correctly.

The drive cables are not
connected properly

Open the system and make sure all cables to
the controller card are connected correctly.
Some systems do not have IDE controller
cards because the IDE controller is built into
the system board.

The drive controller is not
seated properly

Open the system and reseat the drive
controller. Some systems do not have IDE
controller cards because the IDE controller is
built into the system board.

8508088.book Page 114 Thursday, November 1, 2001 9:35 AM

«
...
120
121
122
123
124
...
»

Summary of Contents for 930 series

































































































































































Reviews:

No comments

Related manuals for 930 series

Brand: TANDBERG Pages: 276

SUPERO SuperServer 6026TT-GIBQRF

Brand: Supero Pages: 104

Brand: LTS Pages: 5

Brand: Cobalt Digital Inc Pages: 218

Brand: KYLAND Pages: 30

AirLive WP-203G

Brand: Ovislink Pages: 132

Transport TX46 (B4985) Service

Brand: TYAN Pages: 75

SuperServer 6123L-8R

Brand: Supero Pages: 105

AcquiLite EMB A7810

Brand: Obvius Pages: 29

Brand: Fujitsu Pages: 200

Brand: Asus Pages: 98

Brand: Asus Pages: 84

Brand: hopf Elektronik GmbH Pages: 178

Brand: PROXMOX Pages: 2

Brand: IBM Pages: 5

Brand: QSSC Pages: 98

Brand: QSSC Pages: 99

Brand: 3onedata Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands