Gateway 930 series System Manual Download

Page: 12 / 160

System Features

Back panel

Power supply modules (2)

provide redundant power and hot-plug capability

to power the server with minimal downtime.

Module power switches (2)

provide independent power control for each

redundant power supply module.

Power connector

connects to the server power cord. The other end of the

power cord plugs into an AC outlet or power strip.

Parallel port

Mouse port

Power supply module

Expansion card
retention clips

Expansion
card slots

Power connector

Module power switch

Keyboard port

Serial port A

Video port

USB ports

Redundant
power supply

Power supply module LED

Kensington
lock slot

Power supply

cable clamp

RJ-45 LAN port

8508088.book Page 4 Thursday, November 1, 2001 9:35 AM

Summary of Contents for 930 series

































































































































































Search results

Summary of Contents for 930 series

Reviews:

Related manuals for 930 series

Brands by name

Popular brands

Gateway 930 series, System Manual

Search results

Summary of Contents for 930 series

Reviews:

Related manuals for 930 series

Brands by name

Popular brands